Products

Andur 9-APF-LM is a polyester based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 89 to 92 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

Andur 9500 AP/Curene® 442 is a Polyurethane (Polyether, TDI) (PUR-Ether/TDI) product. It is available in North America.

Andur 7501 DPLF is a polyether (PPG) based liquid, toluene diisocyanate terminated prepolymer containing .1% or less free TDI. An elastomer with a hardness of 74 to 77 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

Andur 1-75 DP is a polyether based liquid isocyanate-terminated prepolymer. An elastomer with a hardness of 73-77 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'- methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, and by the use of plasticizers.

Andur 9002-APTF is a low viscosity liquid prepolymer which can be processed and cured at room temperature with Curene 107 using Oleic acid catalyst to yield an elastomer with a hardness of 88 to 90 Shore A. This system has been specifically formulated to yield a tack-free film in about 60 minutes when catalyzed to a 6 to 8 minute pot life.Andur 9002-APTF is recommended where room temperature processing and curing is desired and a tack-free film within about 60 minutes. If an application does not require a tack-free film, then we recommend using Andur RT 9002 AP.

Andur M-95 AS is a custom formulated MDI based polyurethane elastomer system. It is designed as a low cost, easily processed candidate for use in dunnage applications. M-95 AS is a two component, 1:1 ratio (weight) system that can be processed at room temperature and yields a 95 Shore A elastomer. The system needs no post cure and contains no TDI.

Andur 9500 APLF is a polyether (PPG) based liquid, toluene diisocyanate terminated prepolymer containing 0.1% or less free TDI monomer. An elastomer with a hardness of 95 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by curing Andur 9500 APLF with polyols and their combination with Curene 442 and other diamines, or by the use of plasticizers.

Andur 1-95AP is a polyether (PTMG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 95 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by curing Andur 1-95AP with polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

Andur 7-3 APLF is a polyester based liquid, toluene diisocyanate terminated prepolymer containing 0.1% or less free TDI monomer. An elastomer with a hardness of 70-75 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442, other diamines or through the use of plasticizers.

All properties based on Andur® 8-APF-LM cured with Curene® 3005

Andur 8-5APLS is a polyester based, toluene diisocyanate terminated prepolymer designed for optimum solvent resistance. Elastomers with a Shore A durometer hardness of 83-86 can be obtained when Andur 8-5APLS is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of 53-56 Shore A durometer hardness can be obtained when cured with Curene 49.

Andur 9000-AS is a two-component liquid urethane system which can be processed at room temperature to yield an eastomer with a hardness of 90 to 92 Shore A.Andur 9000-AS is recommended where ease of processing is desired.

Andur 9 APLF is a polyester based liquid, toluene diisocyanate terminated prepolymer containing 0.1% or less free TDI monomer. An elastomer with a hardness of 90 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442, other diamines or through the use of plasticizers.

Andur 6-DP-LM is a polyester based, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 60 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

All properties based on Andur® 2-90AP cured with Curene® 280

Andur 2-92AP is a polyether (PTMG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 92 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or by the use of plasticizers.

Andur 70-DP is a polyether (PTMG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 70 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or by the use of plasticizers.

Andur 2-72DP is a polyether (PTMG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 72 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or by the use of plasticizers.

All properties based on Andur® 9000-AP cured with Curene® 185

Andur 9-3 APLF is a polyester based liquid, toluene diisocyanate terminated prepolymer containing 0.1% or less free TDI monomer. An elastomer with a hardness of 92 to 94 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442, other diamines or through the use of plasticizers.

Andur 8-3 APLF is a polyester based liquid, toluene diisocyanate terminated prepolymer containing 0.1% or less free TDI monomer. An elastomer with a hardness of 81 to 84 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442, other diamines or through the use of plasticizers.

All properties based on Andur® 2-95AP cured with Curene® 280

Andur 8003AS is a 80 Shore A, low cost, high performance urethane. Andur 8003AS offers high rebound and excellent dynamic properties in a moderate to low cost system. In addition, when properly cast, Andur 8003AS gives a water white finished product. Andur 8003AS performs best when cast with Ethacure 100LC through meter mix and dispense equipment however, product modifications are available which may extend working time to offer hand batch opportunities. This system is primarily recommended for applications that require superior dynamic performance, or enhanced product clarity. In addition, low processing temperatures and quick cycle times offer processing advantages.

Andur 5-DPLM is a polyester based, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 50 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by curing Andur 5-DPLM with poyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

All properties based on Andur® 9-AP cured with Curene® 442

Andur 6500 DPLF is a polyether (PPG) based liquid, toluene diisocyanate terminated prepolymer containing 0.1% or less TDI monomer. An elastomer with a hardness of 65 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

Andur 8-6APSLM is a polyester based liquid, toluene diisocyanate terminated prepolymer designed to remain liquid at room temperature. Elastomers with a Shore A durometer hardness of 84-87 can be obtained when Andur 8-6APSLM is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be prepared by curing Andur 8-6APSLM with various polyols, combinations of polyols and Curene 442, other diamines, or through the use of plasticizers.

Andur 80-5AP is a polyether (PTMG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 83-85 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by curing Andur 80-5AP with polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

Andur 75 DGP-2 is a polyether (PTMG) based liquid isocyanate- terminated prepolymer. An elastomer with a hardness of 75 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'- methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, and by the use of plasticizers. Andur 75 DGP-2 was designed to have a longer pot life for those who require more time for casting. Due to its lower %NCO, compared to other 75D materials, Andur 75 DGP-2 is much more economical to process, as approximately 20% less curing agent is required.

Andur 9000-AP is a polyether (PPG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 90 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

Andur 90-AP is a polyether (PTMG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 90 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or by the use of plasticizers.

Andur 8500-AP is a polyether (PPG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 85 to 87 Shore A is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

Andur 6500-DP is a polyether (PPG) based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 65 Shore D is obtained when this prepolymer is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various polyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.

All properties based on Andur® 95-AP cured with Curene® 185

Andur 8-6APSLM is a polyester based liquid, toluene diisocyanate terminated prepolymer designed to remain liquid at room temperature. Elastomers with a Shore A durometer hardness of 84-87 can be obtained when Andur 8-6APSLM is cured with Curene 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be prepared by curing Andur 8-6APSLM with various polyols, combinations of polyols and Curene 442, other diamines, or through the use of plasticizers.

Andur RT 9002 AP is a low viscosity liquid prepolymer which can be processed and cured at room temperature with Curene 107 to yield an elastomer with a hardness of 88 to 92 Shore A. This system has a extended potlife of about 25 minutes that can be adjusted using oleic acid catalyst.Andur RT 9002 AP is recommended where room temperature processing and curing is desired with minimal elastomer shrinkage.