Products

4-phenyl benzophenone is a very fast curing type-II photoinitiator. In the presence of O2, the use of an amine co-initiator is recommended. It is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-3208 Ethoxylated Bisphenol A Dimathacrylate is a difunctional monomer providing low volatility and flexibility.

2-Methyl-1-[4-(methylthio) phenyl]-2-morpholino propan-1-one is a type I photoinitiator primarily used in pigmented systems. It is oftentimes used with PL-ITX as a sensitizer to enhance the curing efficiency in inks. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

Diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide is a Type I photoinitiator best known for it's through cure abilities. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-7210 has a unique combination of high tensile strength and good elongation, which results in excellent toughness upon curing. PL-7210 is also very low color.

PL-7110 is a low color urethane that is a viscous liquid at room temperature. Upon cure, PL-7110 creates a tough polymer with percent elongation near 60%. PL-7110 is non-yellowing and can be used in formulations to add toughness.

PL-7113 is a non-yellowing urethane that exhibits a high degree of elongation. It also has a high rate of conversion with low average shrinkage stress. PL-7113 can be added to formulations to add toughness.

2-hydroxy-2-methyl-1-phenyl-1-propanone is a fast curing type-I photoinitiator. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-7021 has a unique structure which results in a flexible cured product. Adding PL-7021 to formulations has been shown to increase toughness.

PL-4265 is a 50:50 liquid blend of 2-hydroxy-2-methyl-1-phenyl-1-propanone and diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide. It provides exceptional cure response in white and pastel pigmented systems as well as thicker clear films. It provides a perfect balance between surface cure and through cure to enable the best possible adhesion in these systems. PL-4265 soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-3214B is a difunctional reactive monomer that provides excellent diluecy as well as water resist. and weathering prop.

PL-3102 is a monofuctional monomer that provides water resistance and flexibility.

PL-7130 is a low color urethane that is a viscous liquid at room temperature. Upon cure, PL-7130 creates a flexible yet tough polymer with percent elongation near 80%. PL-7130 is non-yellowing and can be used in formulations to add flexibility.

PL-7003 is a low viscosity urethane that exhibits very fast cure speeds. Upon curing, PL-7003 exhibits excellent hardness and very low color. PL-7003 can be used in formulations to add strength.

PL-7002 is a tetrafunctional polymethacrylate. This increased functionality results in faster cure speeds due to increased cross-linking capacity. Upon curing, PL-7002 exhibits very high Shore D hardness values. PL-7002 is non-yellowing and can be used in formulations to add strength.

PL-3100 is a monofunctional monomer with excellent hardness properties.

PL-3110 is a monofunctional monomer providing good adhesion and low viscosity.

PL-3214C is a difunctional reactive monomer that provides excellent diluecy as well as water resist. and weathering prop.

PL-7000 is a low viscosity urethane dimethacrylate. When cured, PL-7000 exhibits good hardness and strength. PL-7000 is low in color.

PL-3203 is a difunctional monomer providing good flexibility and is water soluble.

PL-150 is oligo [ 2-hydroxy-2-methyl-1-[ 4-(1-methylvinyl) phenyl] propanone] and 2-Hydroxy-2-methyl-1-phenyl-1-propanone. It is a very fast curing type-I photoinitiator soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-3216 is a difunctional monomer providing water resistance and fast cure.

PL-3220 is a difunctional monomer providing a good balance of hydrophobicity and hydrophilicity.

PL-7121 is a novel low-shrink urethane monomer based on Esstech's proprietary methacrylate technology. PL-7121 possesses a volumetric shrinkage of 2.0 - 2.5% and conversion of 65 - 80% without filler. PL-7121 has very low color and can be added to formulations to add toughness. PL-7121 possess the excellent combination of superior elongation and strength.

1-hydroxy-cyclohexylphenyl-ketone is a fast curing type-I photoinitiator. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

2-Benzyl-2-dimethylamino-1-(4-morpholinphenyl) butanone is a type I photoinitiator primarily used in non-white pigmented systems. It is oftentimes used with PL-ITX as a sensitizer to enhance the curing efficiency in inks. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-3216A is a difunctional monomer providing water resistance and fast cure.

PL-3116 is a monofunctional monomer providing good adhesion, high Tg, and low viscosity.

PL-3216B is a difunctional monomer providing water resistance and fast cure.

PL-100 is a 70:30 blend of oligo [ 2-hydroxy-2-methyl-1-[ 4-(1-methylvinyl) phenyl] propanone] and 2-Hydroxy-2-methyl-1-phenyl-1-propanone. It is a fast curing type-I photoinitiator soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-500 is a eutectic blend made up of a 1:1 mixture of PL-CPK and PL-BPO. It is well suited for applications where ease of use and good surface cure are needed. PL-500 is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-DRK is a liquid photoinitiator compound developed specifically for dark and black inks and coatings. It provides an optimum balance between surface cure and through cure to enable the best possible adhesion in these systems. Because of it's optimum viscosity, it can be used in flexo, screen and paste inks without negatively effecting rheology. It is also well suited as a press side additive for the printer. PL-DRK is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-7013 has a relatively low viscosity but upon curing exhibits high conversion and low shrinkage. It exhibits excellent flexibility once cured. PL-7013 is very low color.

PL-3201 Polyethylene Glycol 200 Dimethacrylate is dimethacrylate difunctional monomer. It's used in 3D printing,Adhesives and Sealants applications. It provides excellent adhesion, flexibility and impact strength.

Benzil dimethyl ketal is a fast curing type-I photoinitiator. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-3204 is a difunctional monomer providing flexibility and hydrophobicity.