Products

A single component, heat-cured epoxy powder that is lightweight, flame retardant and easy to use. SYMPOXY™ 1960G is typically used for potting electrical components. It is ideal in applications where exothermic or curing temperatures above 85°C cannot be tolerated and where thermal expansion/contraction should not harm delicate components.

RIGIDDI-PAK R-4528 SeriesA black, flame retardant, thermally conductive, high performance series that can be used in all types of electrical components. Combined with its ability to dissipate heat, DI-PAK R-4528 also provides low linear thermal expansion, low shrinkage, and low exothermic heat while curing. Meets UL requirements.

DI-PAK E-4500 SERIESFlexible, 45, 65 and, 95 shore A hardness, potting and encapsulating systems. Flame retardant (FR), accelerated 3 minute (-3) gel time, and black or unpigmented versions are available.

DI-PAK E-4568A tough, REPAIRABLE, shock resistant potting compound for short and long run productions. DI-PAK E-4568 has excellent insulating properties, a very low moisture vapor transmission rate, can be operated from -60°C to +100°C, and performs in both wet and dry environments. It can be easily trimmed with a knife, making repairs quick and easy.

SYMPOXY 1225FR-CA561 is a filled, two component epoxy system that is pigmented black.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

RIGIDDI-PAK R-4806 & R-4807 A/BLow viscosity, fast cure, high performance, potting and encapsulating compounds with excellent properties and FAST TURNOVER. Both are two part systems with 1:1 mix ratios by volume.

A clear amber, 100% solids, room temperature curing epoxy system with a 2:1 mix ratio by volume. 1010-CA810 is great for electrical potting and encapsulating, industrial surface coating, wood surface coating and seal coating. This product has a high gloss finish, low viscosity, and good water/chemical resistance.

DI-PAK E-4500 SERIESFlexible, 45, 65 and, 95 shore A hardness, potting and encapsulating systems. Flame retardant (FR), accelerated 3 minute (-3) gel time, and black or unpigmented versions are available.

RIGIDDI-PAK R-4525 SeriesA general purpose series of low viscosity, strong, potting and encapsulating compounds. DI-PAK R-4525 has excellent electrical insulating properties and bonds well to many substrates. By varying the curing agents, the desired cure and working life can be obtained.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

RIGIDDI-PAK R-4242/4243Low cost, fast set potting compounds with excellent properties and FAST TURNOVER. R-4242/4243 are 1:1 by weight or volume, making them ideal for hand pour or automatic metering systems.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

RIGIDDI-PAK R-4806 & R-4807 A/BLow viscosity, fast cure, high performance, potting and encapsulating compounds with excellent properties and FAST TURNOVER. Both are two part systems with 1:1 mix ratios by volume.

DI-PAK E-4500 SERIESFlexible, 45, 65 and, 95 shore A hardness, potting and encapsulating systems. Flame retardant (FR), accelerated 3 minute (-3) gel time, and black or unpigmented versions are available.

RIGIDDI-PAK R-4528 SeriesA black, flame retardant, thermally conductive, high performance series that can be used in all types of electrical components. Combined with its ability to dissipate heat, DI-PAK R-4528 also provides low linear thermal expansion, low shrinkage, and low exothermic heat while curing. Meets UL requirements.

RIGIDDI-PAK R-4525 SeriesA general purpose series of low viscosity, strong, potting and encapsulating compounds. DI-PAK R-4525 has excellent electrical insulating properties and bonds well to many substrates. By varying the curing agents, the desired cure and working life can be obtained.

RIGIDDI-PAK R-4545 SeriesA very low viscosity potting and encapsulating system with excellent flow and penetration into the most intricate electronic components, without voids or porosity. The R-4545 Series cure to a hard, shiny, high gloss, plastic finish that is free from "blushing" under all humidity conditions. The R-4545 Series is ideal for electrical applications where surface finish and appearance are critical.

RIGIDDI-PAK R-4307A high performance, long working life potting compound for potting/encapsulating units requiring high physical strength and excellent electricals. DI-PAK R-4307 is a holds its mechanical and electrical properties while under the most severe conditions. This is due to its low water absorption, thermal shock resistance, and retention of strength at elevated temperatures.

RIGIDDI-PAK R-4528 SeriesA black, flame retardant, thermally conductive, high performance series that can be used in all types of electrical components. Combined with its ability to dissipate heat, DI-PAK R-4528 also provides low linear thermal expansion, low shrinkage, and low exothermic heat while curing. Meets UL requirements.

DI-PAK E-4500 SERIESFlexible, 45, 65 and, 95 shore A hardness, potting and encapsulating systems. Flame retardant (FR), accelerated 3 minute (-3) gel time, and black or unpigmented versions are available.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

DI-PAK E-4901-2, E-4901-10, & E-4901-30Low cost, easy to use, potting compounds with fast cycle times. Available in 3 speeds.

RIGIDDI-PAK R-4545 SeriesA very low viscosity potting and encapsulating system with excellent flow and penetration into the most intricate electronic components, without voids or porosity. The R-4545 Series cure to a hard, shiny, high gloss, plastic finish that is free from "blushing" under all humidity conditions. The R-4545 Series is ideal for electrical applications where surface finish and appearance are critical.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

DI-PAK E-4701, E-4951 and E-4501Easily pourable, thermally conductive, shock resistant potting compounds that are ideally suited for low and high production applications. This series of DI-PAK products reduce rejects by exhibiting extremely low stress on potted components. All three of the above DI-PAK E products are flame retardant and meet UL 94V-0 requirements.

DI-PAK E-4888 & E-4889High performance, flexible potting systems designed to be in constant water immersion while maintaining electrical and physical properties. DI-PAK E-4888 & E-4889 were designed to meet Naval underwater applications.

DI-PAK E-4500 SERIESFlexible, 45, 65 and, 95 shore A hardness, potting and encapsulating systems. Flame retardant (FR), accelerated 3 minute (-3) gel time, and black or unpigmented versions are available.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

RIGIDDI-PAK R-4525 SeriesA general purpose series of low viscosity, strong, potting and encapsulating compounds. DI-PAK R-4525 has excellent electrical insulating properties and bonds well to many substrates. By varying the curing agents, the desired cure and working life can be obtained.

RIGIDDI-PAK R-4545 SeriesA very low viscosity potting and encapsulating system with excellent flow and penetration into the most intricate electronic components, without voids or porosity. The R-4545 Series cure to a hard, shiny, high gloss, plastic finish that is free from "blushing" under all humidity conditions. The R-4545 Series is ideal for electrical applications where surface finish and appearance are critical.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

DI-PAK E-4501 Easily pourable, thermally conductive, shock resistant potting compounds that are ideally suited for low and high production applications. This series of DI-PAK products reduce rejects by exhibiting extremely low stress on potted components. All three of the above DI-PAK E products are flame retardant and meet UL 94V-0 requirements.

DI-PAK E-4888 & E-4889High performance, flexible potting systems designed to be in constant water immersion while maintaining electrical and physical properties. DI-PAK E-4888 & E-4889 were designed to meet Naval underwater applications.

RIGIDDI-PAK R-4242/4243Low cost, fast set potting compounds with excellent properties and FAST TURNOVER. R-4242/4243 are 1:1 by weight or volume, making them ideal for hand pour or automatic metering systems.

RIGIDDI-PAK R-4525 SeriesA general purpose series of low viscosity, strong, potting and encapsulating compounds. DI-PAK R-4525 has excellent electrical insulating properties and bonds well to many substrates. By varying the curing agents, the desired cure and working life can be obtained.