Products

Material Glass Formulated PTFE Features/Benefits Excellent heat, wear, and chemical resistance. Good cryogenic properties. Caution: can be abrasive running against soft metals at high surface speed. Excellent material for back-up rings. Working Temperature Range -450° to +600°F [-268° to +316°c] Color Yellow

Features/Benefits: Color: White FDA compliant Low gas permeability Good cryogenic properties Limited wear and heat resistance Working Temperature Range: -268° to +260°C [-450° to +500°F]

Rulon® J is an all-polymeric reinforced, light brown colored PTFE compound that operates exceptionally well against soft mating surfaces such as 316 stainless steel, aluminum, mild steel, brass and other plastics. The unique "shaft friendly" material is also low in friction and wear and is self lubricating.Rulon J has one of the lowest coefficients of friction of most reinforced PTFE materials. This makes it ideally suited for start/stop applications where stick-slip must be eliminated. The tribological properties of this material also make it suitable for both bearing and wear component applications.

Rulon® AR is somewhat more flexible than Rulon® LR, hence suitable for seals and bonded coating of slide surfaces. It has many decades of use in automotive shaft seals and fuel metering pump cups.Rulon AR has a practically universal chemical inertness like that of Rulon LR and provides long life and reliability in continuous non-lubricated service. It is capable of operating at PV values up to approximately 10,000. Higher PV values are possible for intermittent use applications.

Rulon® 945 is a black PTFE-based material that has very low wear and deformation under load, making it ideally suited for demanding thermal applications. In fact, its deformation is the lowest of all Rulon® grades. It also possesses excellent chemical resistance and good dimensional stability.Rulon 945 is best suited for use against hard mating surfaces, like hardened steel substrates since it does have moderate abrasive qualities. It is not suitable in applications where electrically insulating properties are required.

Rulon® W2 is a black PTFE-based material developed for use in fresh-water applications. It exhibits low friction and excellent wear characteristics (one of the lowest wear rates in fresh water) as well as good thermal dissipation, preventing shaft distress. Its properties are enhanced when wet.It is compatible with most metal substrates and soft mating surfaces. Rulon W2 is a good alternative to Rulon J when superior chemical resistance is needed. However, it should not be used on very soft mating surfaces or where electrical insulation is desired.

Features/Benefits: Color: Dark Gray Particularly suitable for water and steam service Excellent general purpose material for heat and wear resistance Recommended for dry and poorly lubricated applications Working Temperature Range: -268° to +260°C [-450° to +500°F]

Rulon® 1337 is a tan material made entirely from FDA compliant components. It has excellent physical properties and is chemically compatible with most chemicals, except concentrated sulfuric acid. This offers much flexibility in wash-down environments of food and pharmaceutical processing environments. It has a slightly lower coefficient of friction than Rulon J, offering extended life and less abrasion with softer mating surfaces. It is compatible with most commercially available natural lubricants for additional reduction in friction.

Features/Benefits: Color: Dark Gray Soft material Good for sealing at low pressures Can be abrasive running against soft metals Good heat resistance Working Temperature Range: -268° to +316°C [-450° to +600°F]

Features/Benefits: Color: Gold Extremely tough, long wearing material Limited heat and chemical resistance Excellent in water and water-based fluids, particularly suitable for abrasive media Recommended for long wear life under severe conditions Working Temperature Range: -268° to +82°C [-450° to +180°F]

Aqua colored low deformation material suitable for linear bearings and slides Rulon® 142 is a specially formulated dull blue-green linear bearing material that exhibits low wear, high thermal dissipation, and good dimensional stability characteristics.Among its many benefits are the virtual elimination of stick-slip, vibration dampening, self-lubrication, uniform friction, long life, ease of application and design diversity.Rulon 142 has excellent mechanical properties and is the ideal material for machine tool applications. Its low deformation characteristics limit the amount of misalignment that can occur with other bearing materials.Strong acids and bases should be avoided, as they may attack the fillers.

Rulon® 1410 is a gold material with excellent elongation and tensile strength suitable for flip seal and other flexible sealing applications. Coupled with low frictional characteristics, it offers the added benefit of energy savings and/or increased sealing efficiency.This material is also resistant to most harsh chemicals. It is also compatible with many commercially available lubricants for additional reduction in torque. It can also be used as a liner material for substrates requiring any of the above characteristics.

Rulon® 957 is a speckled green material that was developed specifically for noise dampening and abrasion resistance, such as in commercial or residential clothes dryers.It provides low friction operation on softer mating surfaces at higher loads than Rulon® J.This material also offers excellent performance on coated metals, particularly porcelain. Among its many benefits are an overall reduction of the weight of the finished product, vibration absorption, and cost reduction due to rapid manufacturing methods.

Rulon® F by Saint-Gobain is comprised of Polytetrafluoroethylene. It is commonly used

Features/Benefits: Color: Tan Superior wear and heat resistance running against soft metals Non-abrasive Recommended for moderate to high speed dynamic service Working Temperature Range: -268° to +288°C [-450° to +550°F]

Rulon® 123 is a glossy black non-abrasive compound for softer mating surfaces, such as stainless steel. This material has excellent chemical resistance and is FDA and USDA compliant. It is less expensive than Rulon J, but is slightly less flexible and higher in wear. It has a high resistance to deformation, low coefficient of friction and good thermal and electrostatic dissipation.This material has a maximum operating temperature of 550°F (300°C). Rulon 123 releases black wear debris over time and should not be used in ultra-dry, vacuum applications, or where electrical insulation is desired.

Rulon® XL is a tan colored material that is best for use against aluminum (including anodized) substrates. Rulon XL exhibits very low wear as compared with other Rulon® grades.Other advantages offered by this unique material are that it combines low deformation under load with exceptionally good chemical resistance. It is compatible with a wide range of mating surfaces, but is not recommended for use with alkalis. Its non-abrasive character enhances the frictional performance to prevent galling of softer mating surfaces. It is the best material for vacuum service.

Rulon® LR is a maroon colored bearing material best known for its versatile design properties.It is compatible with most hardened steel substrates. Mild steel is acceptable; harder running surfaces are better.Rulon® has a practically universal chemical inertness. Of the chemicals encountered in commercial practice, only molten sodium and fluorine, at elevated temperatures and pressures, show any signs of attack.For continuous non-lubricated service, Rulon LR sleeve bearings are capable of operating up to 10,000 PV. Higher values are possible for intermittent service.

Rulon® 488 is a dull turquoise material originally developed for use with painted surfaces. It has been used in veneer dryer bearings in the plywood industry.Its excellent wear resistance, especially in extremely dry environments, make it a material of choice in hydrogen and natural gas compressors. Its almost universal chemical resistance enables it to withstand corrosives and acids sometimes present in trace amounts in these environments.It has a higher load capacity than Rulon® J and better abrasion resistance than both Rulon® J and Rulon® 123.

Rulon® 1045 is a dull gold material that has an excellent ability to elongate in a flip seal application. Coupled with excellent frictional characteristics, it offers the added benefit of energy savings, as well as increased sealing efficiency.This material is also resistant to many harsh chemicals found in the application environments where it is typically used. It is also compatible with most commercially available lubricants for additional reduction in friction. Its low deformation properties allow it to be effective as a bearing or sliding surface.

Rulon® 641 is manufactured from FDA compliant materials which possess excellent load and wear characteristics.It offers excellent, continuous non-lubricated service up to 10,000 PV - higher for intermittent service. While the load capacity of Rulon 641 is generally limited to 1,000 psi at room temperature, deformation is a function of wall thickness, temperature and load.Its compatibility with a wide array of mating surfaces, including mild steel, 303 and 316 stainless steels, as well as harder materials, make it a good choice for most food and pharmaceutical bearing applications.

Features/Benefits: Color: Tan Resistant to abrasions Working Temperature Range: Up to +260°C [+500°F] Chemical and environmental inertness Good strength at elevated temperatures

Rulon® 1439 is a white FDA compliant material that is suitable for immersed service with better wear characteristics than most other PTFE compounds. Its color makes it esthetically pleasing for food and pharmaceutical applications.This material is also resistant to many harsh chemicals found in the application environments where it is typically used. It is compatible with most commercially available lubricants for additional reduction in friction. Its properties allow it to be effectively utilized as a bearing or sliding surface.