Products

SynFoam DW is a high performance syntactic foam designed for the most critical deep water applications. SynFoam DW has the highest strength to weight ratio of all SynFoam grades and allowing the end users to ultimately reduce the weight of the buoyancy package. Our DW series ranges in density from 31 to 41 pounds per cubic foot and is highly recommended for 5K and 6K ROV's as well as other deep water submersibles. SynFoam DW is available as 4.5” x 11.5” x 11.5” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam DW we also provide final module fabrication services. Services include machining, assembly, and finishing with a quality marine based paint.

SynFoam HT is a high performance, light weight pre-cast syntactic foam that provides the best combination of high temperature resistance and dielectric properties. SynFoam HT has a low coefficient of thermal expansion and good strength. In addition to being used for weight reduction SynFoam HT is also used in the microwave industry because of the dielectric properties which show outstanding performance over a wide frequency range up to 10 GHz. SynFoam HT is an ideal structural core material for applications that will be exposed to higher temperatures and has been used to replace honeycomb structures. SynFoam HT is chemically stable, UV resistant and does not absorb water. SynFoam HT is available as 4” x 12” x 12” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam HT we also provide final fabrication services. Services include machining, assembly, and finishing with a quality coating.

SynFoam HP is a high performance syntactic foam designed to safely operate in underwater environments. SynFoam HP resists water absorption and provides excellent performance for deep water submersion in both manned and unmanned vehicles. These properties have made SynFoam HP a crucial component of ROV, AUV, UUV, and HOV underwater vehicles as well as buoyancy modules designed by industrial professionals. Our HP series of foams range in density from 20 to 32 pounds per cubic foot and are highly recommended for 1K, 2K, 3K, and 4K ROV's. SynFoam HP is available as 6” x 12” x 24” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam HP we also provide final module fabrication services. Services include machining, assembly, and finishing with a quality marine based paint.

SynFoam HP is a high performance syntactic foam designed to safely operate in underwater environments. SynFoam HP resists water absorption and provides excellent performance for deep water submersion in both manned and unmanned vehicles. These properties have made SynFoam HP a crucial component of ROV, AUV, UUV, and HOV underwater vehicles as well as buoyancy modules designed by industrial professionals. Our HP series of foams range in density from 20 to 32 pounds per cubic foot and are highly recommended for 1K, 2K, 3K, and 4K ROV's. SynFoam HP is available as 6” x 12” x 24” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam HP we also provide final module fabrication services. Services include machining, assembly, and finishing with a quality marine based paint.

SynFoam DW is a high performance syntactic foam designed for the most critical deep water applications. SynFoam DW has the highest strength to weight ratio of all SynFoam grades and allowing the end users to ultimately reduce the weight of the buoyancy package. Our DW series ranges in density from 31 to 41 pounds per cubic foot and is highly recommended for 5K and 6K ROV's as well as other deep water submersibles. SynFoam DW is available as 4.5” x 11.5” x 11.5” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam DW we also provide final module fabrication services. Services include machining, assembly, and finishing with a quality marine based paint.

SynFoam DW is a high performance syntactic foam designed for the most critical deep water applications. SynFoam DW has the highest strength to weight ratio of all SynFoam grades and allowing the end users to ultimately reduce the weight of the buoyancy package. Our DW series ranges in density from 31 to 41 pounds per cubic foot and is highly recommended for 5K and 6K ROV's as well as other deep water submersibles. SynFoam DW is available as 4.5” x 11.5” x 11.5” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam DW we also provide final module fabrication services. Services include machining, assembly, and finishing with a quality marine based paint.

SynFoam MW is a moderate cost, high performance syntactic foam designed for the most critical deep water applications. SynFoam MW has an excellent strength to weight ratio and a better cost/performance benefit than SynFoam DW. MW is typically chosen for use where cost rather than density is the primary factor in selection of syntactic foam for deep water applications. MW is offered in densities between 30 and 44 pounds per cubic foot and provides the performance necessary for standard 5K and 6K ROV's as well as other underwater vehicles where a high strength is required. SynFoam MW is available as 6” x 12” x 24” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam MW we also provide final module fabrication services. Services include machining, assembly, and finishing with a quality marine based paint.

SynFoam MW is a moderate cost, high performance syntactic foam designed for the most critical deep water applications. SynFoam MW has an excellent strength to weight ratio and a better cost/performance benefit than SynFoam DW. MW is typically chosen for use where cost rather than density is the primary factor in selection of syntactic foam for deep water applications. MW is offered in densities between 30 and 44 pounds per cubic foot and provides the performance necessary for standard 5K and 6K ROV's as well as other underwater vehicles where a high strength is required. SynFoam MW is available as 6” x 12” x 24” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam MW we also provide final module fabrication services. Services include machining, assembly, and finishing with a quality marine based paint.

SynFoam HP is a high performance syntactic foam designed to safely operate in underwater environments. SynFoam HP resists water absorption and provides excellent performance for deep water submersion in both manned and unmanned vehicles. These properties have made SynFoam HP a crucial component of ROV, AUV, UUV, and HOV underwater vehicles as well as buoyancy modules designed by industrial professionals. Our HP series of foams range in density from 20 to 32 pounds per cubic foot and are highly recommended for 1K, 2K, 3K, and 4K ROV's. SynFoam HP is available as 6” x 12” x 24” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam HP we also provide final module fabrication services. Services include machining, assembly, and finishing with a quality marine based paint.

SynFoam HT is a high performance, light weight pre-cast syntactic foam that provides the best combination of high temperature resistance and dielectric properties. SynFoam HT has a low coefficient of thermal expansion and good strength. In addition to being used for weight reduction SynFoam HT is also used in the microwave industry because of the dielectric properties which show outstanding performance over a wide frequency range up to 10 GHz. SynFoam HT is an ideal structural core material for applications that will be exposed to higher temperatures and has been used to replace honeycomb structures. SynFoam HT is chemically stable, UV resistant and does not absorb water. SynFoam HT is available as 4” x 12” x 12” fully cured blocks. The blocks may be further machined into different sizes and shapes by the end user to meet the necessary specific tolerances and requirements. Our syntactic foam is easily bonded together with the use of our syntactic adhesive to form large structures. If you have a specific design for use with SynFoam HT we also provide final fabrication services. Services include machining, assembly, and finishing with a quality coating.