Knowde Enhanced TDS
Identification & Functionality
- Technologies
- Product Families
- Components
Two part system; 1:1 ratio
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Product Highlights
The 1007 PolyUrea is a true polyurea and not a hybrid. Application substrate temperatures; -20°F to 200°F. The 1007 is applied via a Graco Reactor Hydraulic Proportioner or Arma Proportioner or equal. Use B side agitator and feed pumps for A and B drums.
1007 conforms to the requirements of the USDA for incidental food contact.
- Advantages
- Excellent elongation-400%+
- Excellent for containment, refineries, chemical
- Plants, marine applications and other industrial
- Faciluties
- Designed to chemically bond to astc primers
- Protects concrete and other surfaces, wood, metal, etc.
- Chemical resistant
- High impact & abrasion resistance
Applications & Uses
- Applications
- Application Method
- Use Areas
- Secondary containment with non-skid
- Corrosive barrier, protective coating protection
- Processing equipment
- Concrete tanks &steel tanks
- Secondary containment walls and floors
- All industrial service surfaces
- Geotextile containment appucations
- Preparation
Concrete must have a minimum 28 day cure prior to application. Remove any curing agent, form release materials, oils, wax, moisture or any material that may affect bonding. Clean and wash to remove contaminants and maintain pH 8.0-11.0. Perform a Moisture Vapor Test before making the coating application on concrete. Provide rough surface profile minimum 2-3 mils. Seal/repair all bug-holes, cracks and spalls, see ASTC data sheets on 830, 4034 and 3004 joints).
- Prime
Prime ith ASTC primer PenPrime. Prime 2-4 hours prior to the 1007 application for best results. Spray the polyurea on the primer only after the primer has become tack free.
- Application
Use only heated high pressure equipment & impingement gun equipment, fluid pressure of 2,000 psi. Minimum heat 160F. Surface temperature -209F to 120 F. Apply at not less than 59F above dew point. Apply at specified mil thickness over primer as required for the application. Spraying 1007 requires special equipment, user must be a professional applicator qualified in the use of high performance polyurea materials and specialty application equipment.
- Limitations
Do not use on wet surfaces or expose part A to moisture. Keep out of direct sunlight, store drum kits on wood pallets at room temperature. Always mix the part B before using, continue agitation of Part B during application. Pre- heat drums as needed per environmental temperature. Best results over vapor barrier and/or compatible primer.
- Finish
The finish of this product is best using a stipple surface with the 1007 over freshly applied 1007.
Properties
- Typical Properties
- Unique Properties
- 8 to 20 second set time
- Tack free in 30 seconds
- Higher bond strengths to substrate 400% elongation
- *Formulated for flex strength and adhesion with high tensile strength
| Value | Units | Test Method / Conditions | |
| Solids | 100.0 | % | - |
| Hardness | 95.0 | Shore A | - |
| Mix Ratio | 1:1 | - | - |
| Density | 70.0 | - | ASTM D1622 |
| Abrasion ASTM D1630 CS-17 wheel w/1000gm/500 cycles | 530 NBS | - | - |
| Tack Free | 30.0 | Seconds | ASTM D2471 |
| Tensile | 3600.0 | - | ASTM D412 |
| Tear Strength | 420.0 | Ibs./in. | ASTM D470 |
| Gel Time (75°F) | 65.0 | Seconds | - |
| Elongation | 6.35 | % | ASTM D124 |
| Processing Temperature | 160.0 | °F | - |
| Viscosity ( 75°F cps, A ) | 800-1200 | - | - |
| v.o.c. Content | Ogrms/itr | - | - |
| Permeability | 0.0947 | - | ASTM E96 |
| Maximum mils per coat | unlimited | - | - |
| VOC Content | 0.0 | gms /1 | - |
| Viscosity (75°F cps, B) | 600-900 | - | - |
Technical Details & Test Data
- Moisture Vapor Reduction
1007 should be applied to concrete surfaces as part of a "systems approach". Since concrete will out-gas causing pinholes, using the CMW vapor barrier treatment for the concrete and the Penprime as the primer, pinholes are reduced.
- Priming
1007 cross-links with the ASTC primer PenPrime and produces excellent results when used together as a system.
- Speed &Set Time
Adjustable from a gel time of 8-20 seconds and a set time approximately 10 to 30 seconds.
- Note:
The best spray application results are obtained coating concrete when the ambient temperature is decreasing. In applications where it is not possible to use the temperature to your advantage it is suggested that the ASTC's CMW be used in conjunction with PenPrime and the polyurea coating.
- Curing Time
As soon as the sprayed surface will allow access not more then 1-1.5 hours after first application. Full cure in 24 to 48@70°F
Safety & Health
- safety
This product is for use by professional applicators only. Wear Protective Clothing and gloves as the product bonds very well to fabrics. Read MSDS before using this product. DOT/Flash Point Non-flammable Liquid Classification, not regulated.
Packaging & Availability
- Color
Black, Dark Gray, Tan
- Packaging
110 gallon kits
Storage & Handling
- Shelf Life
1 year, store between 40°F and 100°F.
- Potlife
none
.- Shelf Life
1 year