Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- HRAC/WSSA Group
- Agrochemical Functions
- Technologies
- Product Families
- Composition
ACTIVE INGREDIENT:
2-ethylhexyl ester of 2,4-cdichlorophenoxyacetic acid* - 61.74%
OTHER INGREDIENTS - 38.26%
*Equivalent to 40.9% of 2,4 isomer of 2,4-D or not less than 3.76 pounds of the 2,4 isomer of 2,4-D per gallon.
Features & Benefits
- Labeling Claims
- Product Features
• SolveTM 2,4-D is a solvent-free formulation that has excellent mixing properties.
• SolveTM 2,4-D is a low-volatile ester formulation that is very eff ective in controlling more than 90 broadleaf weeds when applied at the young and active growing stage.
• Broad label use makes SolveTM 2,4-D a product of choice for growers.
- Product Information
ACTIVE INGREDIENT: 2,4-D Ester
HERBICIDE GROUP: 4
ACTIVE INGREDIENT PER GALLON: 3.8 lbs.
MODE OF ACTION: Synthetic auxin growth regulator
PACKAGING: 2x2.5’s, 30’s and 265 gal
Applications & Uses
- Markets
- Applications
- Application Technique
- Herbicide Target Species
- Product Use Rate
CEREAL GRAINS
(Wheat, Barley, Millet, Oats, Rye) (Not under seeded with Legumes)
CROP/APPLICATION TIMING SOLVE™ 2,4-D (pt/acre) SPECIFIC USE DIRECTIONS Wheat, Barley, Millet Rye Annual and biennial & Broadleaf weeds 1/2 to 2 † Apply after crop is fully tillered, but before boot stage of growth (usually 4 to 8 inches tall) and weeds are small. Do not apply before tillering or from early boot through the milk stage of growth. Wheat, Barley, Millet Rye Perennial broadleaf weeds 1 to 2 † Oats (Spring Seeded) 1/2 Apply after crop is fully tillered, but before boot stage of growth (usually 4 to 8 inches tall) and weeds are small. Do not apply before tillering or from early boot through the milk stage of growth. Do not apply during or immediately following cold weather. Oats (Fall Seeded Southern) 3/4 to 1 1/4† Preharvest application (all cereals) 1 Apply using air or ground equipment to control weeds that could interfere with harvest, or to suppress perennial weeds. Apply when grain is in dough stage. Do not apply from early boot through the milk stage of growth. † Use the lower rate in the rate range if small annual or biennial weeds are the major problem. Use the higher rate if perennial weeds or biennial weeds are present that are considered to be hard-to-kill as determined by local experience. Higher rates increase the risk of crop injury and should be used only where weed control justifies such risk. Do not apply SOLVE™ 2,4-D at the crop seedling stage of growth. Consult State Agricultural Experiment Station or Extension Service weed specialists for recommendations or suggestions to fit local conditions.
CEREAL GRAIN RESTRICTIONS
POSTEMERGENCE
• Make no more than one application per crop cycle.
• Do not apply more than 2/3 pints per acre per application.
PREHARVEST
• Make no more than one application per crop cycle.
• Do not apply more than 1 pint per acre per application.
• Pre-Harvest Interval is 14 days.
• Do not graze lactating dairy cattle in treated areas for 14 days after application. Remove meat animals from freshly treated areas 7 days before slaughter.
• Do not harvest hay from treated grain fields.
SolveTM 2,4-D contains 0.47 pounds a.e. of 2,4-D per pint. When tank mixing with products that contain 2,4-D, do not exceed a combined total of 1.75 pounds of a.e. per acre per year.
NON-CROPLAND AREAS
Such as fencerows, hedgerows, roadsides, drainage ditches, rights-of way, utility power lines, railroads, airports, and other non-crop areas
TREATMENT SITE METHOD OF APPLICATION SOLVE™ 2,4-D (pt/acre) SPECIFIC USE DIRECTIONS Annual broadleaf weeds 2 to 4 Apply when annual weeds are small and growing actively before the bud stage. Biennial and perennial weeds should be rosette to bud stage, but not flowering at the time of application. For difficult to control perennial broadleaf weeds and woody species, tank mix up to 4 qt of SOLVE™ 2,4-D plus 1 to 8 pints of Triclopyr 3A herbicide per acre. For ground application: (High volume) apply a total spray volume of 100 to 400 gallons per acre; (low volume) apply a total spray volume of 10 to 100 gallons per acre. For helicopter: Apply a total spray volume of 5 to 30 gallons per acre. Biennial and perennial broadleaf weeds and susceptible woody plants 4 to 8 Spot Treatment to control broadleaf weeds See Instructions for “Spot Treatment” under “Application Instructions” Note: To control broadleaf weeds in small areas with a hand sprayer, use an application rate equivalent to the recommended broadcast rate and spray to thoroughly wet all foliage. See rate conversion table and instructions for “Spot Treatment” and use of hand-held sprayer under “Application Instructions” on the label. Tree Injection Application See instructions for tree injection application in “Forestry Uses” section of the label. Southern wild rose Broadcast application up to 4 Apply in a spray volume of 5 or more gallons per acre by aircraft or 10 or more gallons per acre by ground equipment. Southern wild rose
Spot treatment
8 pints/100 gal of spray Apply when foliage is well developed. Thorough coverage is required. Use 8 pints of SOLVE™ 2,4-D plus 4 to 8 fluid ounces of an agricultural surfactant per 100 gallons of water. Two or more treatments may be required. WEED CONTROL RESTRICTIONS
POSTEMERGENCE (ANNUAL & PERENNIAL WEEDS)
• Do not make more than 2 applications per year.
• Do not apply more than 4 pints per acre per application.
• Minimum spray interval between applications is 30 days.
PREHARVEST (WOODY PLANTS)
• Do not make more than 1 application per year.
• Do not apply more than 8 pints per acre per application. Applications to non-cropland areas are not applicable to treatment of commercial timber or other plants being grown for sale or other commercial use, or for commercial seed production, or for research purposes.
FALLOWLAND AND CROP STUBBLE
Fallowland is considered to be idle cropland, postharvest to crops or between crops.
TYPE OF WEED SOLVE™ 2,4-D (pt/acre) SPECIFIC USE DIRECTIONS Annual broadleaf weeds 1 to 2 Use a lower rate in the rate range when weeds are small (2 to 3 inches tall) and actively growing. Use a higher rate in the rate range when weeds are larger and under less favorable growth conditions. Biennial broadleaf weeds 2 to 4 Apply when musk thistles or other biennial species are in the seedling to rosette stage and before development of flower stalks. The lower rate can be used in the spring during the rosette stage. Use the highest rate in the fall or after flower stalks have developed Perennial broadleaf weeds 2 to 4 Apply when perennial weeds are in bud to early bloom stage or while in good vegetative growth. Wild garlic and onion in crop stubble 4 Apply to new regrowth of wild garlic or onion that occurs in the fall after harvest of other crops. FALLOW LAND RESTRICTIONS
• Only labeled crops can be planted within 30 days of application.
• Do not apply more than 4 pints per acre per application.
• Do not make more than 2 applications per year.
• Minimum spray interval between applications is 30 days.
SolveTM2,4-D contains 0.47 pounds a.e. of 2,4-D per pint. When tank mixing with products that contain 2,4-D, do not exceed a combined total of 4.0 pounds of a.e. per acre per year.
RANGELAND, ESTABLISHED GRASS PASTURES
(Including Perennial Grasslands Not In Agricultural Production Such As Conservation Reserve Program Acres)
TARGET WEEDS OR WOODY PLANTS SOLVE™ 2,4-D (pt/acre SPECIFIC USE DIRECTIONS Annual broadleaf weeds 2 For best results, apply when weeds are small and growing actively before the bud stage. Apply when musk thistles or other biennial species are in the seedling to rosette stage and before flower stalks appear. Refer to the “Weeds Controlled” section of the label for a listing of susceptible weed species and weeds that may be only partially controlled and require repeat applications and/or use of higher recommended rates, even under ideal conditions of application. Biennial and perennial broadleaf weeds 2 to 4 Spot Treatment to control broadleaf weeds See Instructions for “Spot Treatment” under “Application Instructions” Note: To control broadleaf weeds in small areas with a hand sprayer, use an application rate equivalent to the recommended broadcast rate and spray to thoroughly wet all foliage. See rate conversion table and instructions for “Spot Treatment” and use of hand-held sprayers under “Application Instructions.” Tree Injection Application See instructions for tree injection application in “Forestry Uses” section. Wild garlic and wild onion 4 Make three applications (fall-spring-fall or spring-fall-spring) starting in late fall or early spring. Broadleaf weed control in newly sprigged coastal bermudagrass 2 to 4 Applications may be made either preemergence or postemergence. Follow “Specific Use Directions” for annual, biennial and perennial broadleaf weed control, above. Southern wild rose Broadcast application up to 4 Apply in spray volume of 5 or more gallons per acre by aircraft or 10 or more gallons per acre by ground equipment. Southern wild rose Spot treatment 8 pints/100 gal of spray Apply when foliage is well developed. Thorough coverage is required. Use 8 pints of Solve™ 2,4-D plus 4 to 8 fluid ounces of an agricultural surfactant per 100 gallons of water. Two or more treatments may be required. Do not exceed 4 pt per acre per application. CRP Acres - For program lands such as CRP, consult program rules to determine whether grass or hay may be used. The more restrictive requirements of the program rules or this label must be followed. PASTURE & RANGELAND RESTRICTIONS
• For susceptible annual and biennial broadleaf weeds do not exceed 2 pints per acre per application. For moderately susceptible biennial and perennial broadleaf weeds and woody plants, do not exceed 4 pints per acre per application.
• Do not apply more than 2 pints per acre per application for spot treatments.
• Do not make more than 2 applications per year.
• Minimum spray interval between applications is 30 days.
• Pre-Harvest Interval for cut forage for hay is 7 days
• If grass is to be cut for hay, Agricultural Use requirements for the Worker Protection Standard are applicable.
SolveTM 2,4-D contains 0.47 pounds a.e. of 2,4-D per pint. When tank mixing with products that contain 2,4-D, do not exceed a combined total of 1.75 pounds of a.e. per acre per year.
- Directions for use
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation. Do not apply this product through any type of irrigation system. Use of this product in certain portions of California, Oregon, and Washington is subject to the January 22, 2004 Order for injunctive relief in Washington Toxics Coalition, et. Al. v. EP, C01-132C, (W.D. WA) For further information, please refer to http://www.epa.gov/espp/wtc .
Properties
- Formulation Type
- Physical Form
Safety & Health
- Precautionary Statements
Causes eye irritation. Harmful if swallowed or absorbed through skin. Avoid contact with skin, eyes, or clothing. Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals.
- Personal Protective Eqiupment
Some materials that are chemical-resistant to this product are butyl rubber, natural rubber, neoprene or nitrile rubber. If you want more options, follow the instructions for Category A on an EPA chemical-resistance category selection chart.
All mixers, loaders, applicators, flaggers, and other handlers must wear:
1. Long-sleeved shirt and long pants
2. Shoes and socks
3. Chemical-resistant gloves
4. Chemical-resistant apron when applying with any handheld nozzle or equipment, mixing or loading, cleaning up spills or equipment, or otherwise exposed to the concentrate.
If this container contains over 1 gallon and less than 5 gallons, mixers and loaders who do not use a mechanical system (probe and pump) to transfer the contents of this container must wear coveralls or a chemical-resistant apron in addition to the other required PPE.
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry. After each day of use, clothing or PPE must not be reused until it has been cleaned.
- User Safety Recommendations
Users should:
1. Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet.
2. Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing.
3. Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.
- Environmental Hazards
This pesticide may be toxic to fish and aquatic invertebrates. Do not apply directly to water, or to areas where surface water is present, or to intertidal areas below the mean high water mark. Drift and runoff may be hazardous to aquatic organisms in water adjacent to treated areas. Do not contaminate water when disposing of equipment washwaters or rinsate. Apply this product only as directed on label. This chemical has properties and characteristics associated with chemicals detected in groundwater. The use of this chemical in areas where soils are permeable, particularly where the water table is shallow, may result in groundwater contamination. Application around a cistern or well may result in contamination of drinking water or groundwater. Most cases of groundwater contamination involving phenoxy herbicides such as 2,4-D have been associated with mixing/loading and disposal sites. Caution should be exercised when handling 2,4-D pesticides at such sites to prevent contamination of groundwater supplies. Use of closed systems for mixing or transferring this pesticide will reduce the probability of spills. Placement of the mixing/loading equipment on an impervious pad to contain spills will help prevent groundwater contamination.
Packaging & Availability
- Packaging Type
Storage & Handling
- Storage and Disposal
Do not contaminate water, food or feed by storage or disposal.
PESTICIDE STORAGE: Open dumping is prohibited. Do not store this product near fertilizers, seeds, insecticides or fungicides. Do not store near heat or open flame. Re-close all partially used containers by thoroughly tightening screw cap. Absorb any spill with a suitable clay absorbent and dispose of as indicated under “Pesticide Disposal.”
PESTICIDE DISPOSAL: Pesticide wastes are toxic. Improper disposal of excess pesticide, spray mixture or rinsate is a violation of Federal Law and may contaminate groundwater. If these wastes cannot be disposed of by use according to label instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste representative at the nearest EPA Regional Office for guidance.