Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Advantages
- Unparalleled tannin blocking: Prevents darkening from heavy spots
- Will coat a wide range of exotics without color change
- Single component
- Crystal clear color
- Low 275 VOC
- Wet finish indicator: Color will appear milky when wet
- so that you can see missed spots
- Product Highlights
Lock ‘N Seal™ gives you the solution to the unsightly problems of tannin pull. This pre-catalyzed waterbased sealer has a specific blend of resins and solvents formulated to lock out the tannin pull problem. Tannin pull is especially prevalent on White Oak and many exotic species of flooring. This pre-catalyzed waterbased sealer with unparalleled tannin blocking characteristics prevents darkening from heavy spots and applicator marks. Lock ‘N Seal™ dries crystal clear delivering a flawless floor. Lock ‘N Seal makes sealing floors easier!
Wet Finish Indicator
The finish will appear milky when wet so you can see any missed spots. Heavy spots and applicator marks are no longer a worry — Lock ‘N Seal dries crystal clear.
Applications & Uses
- Markets
- Application Method
- Compatible Substrates & Surfaces
- Recommended Uses
- Commercial – Meets ADA requirements for use in hotels, restaurants, shopping centers, dance floors, classrooms, stages, offices, and retail establishments.
- Sports – Gymnasiums, exercise and aerobic floors.
- Exotics or anywhere tannin pull may be an issue.
- Application
• Use Basic Coatings® T-bar, Paint Pad or Roller.
Recommended Systems
- Full Sand - 1-2 coats Lock ‘N Seal followed by 2 coats of any Basic Coatings waterbased finishes.
- NOTE: On white oak or exotic species, 2 coats Lock ‘N Seal will minimize tannin pull.
Application Over Stains And Paints
Allow oil stains to dry per manufacturer’s directions or longer depending on environmental conditions. Apply 2 coats Lock ‘N Seal followed by 1-2 coats of any Basic Coatings waterbased finishes. A test board is recommended with any stain to insure compatibility and color acceptance.
Adding Water
Up to 12 ounces of water can be added per gallon of finish. Adding water will increase the flow and level time during situations of high temperature and low humidity
Surface Preparation
- Before sanding, clean the floor using Basic Coatings’ Squeaky™ Cleaner following label instructions. Cleaning should be done to remove contaminants from the floor before sanding.
- Sand floors using accepted NWFA/MFMA procedures. All old finish must be removed. A NIOSH approved dust mask should be worn during sanding.
- Finish sanding with a new 120-grit screen. DO NOT USE STEEL WOOL.
- Vacuum. Tack with a clean, dry Basic Coatings’ Microfiber Mop until all dust has been removed.
Sealer Application
Always maintain adequate ventilation during all phases of the coating and drying process.
- Measure moisture content of floor in several areas.
- Shake and rock container several times. Use a stir stick to redisperse any settlement.
- Set aside for approximately 10 minutes to allow bubbles to break.
- Rinse refill applicator and remove all excess water. This also helps to remove loose fibers.
- Apply Lock ‘N Seal™ using standard waterbased application procedures.
- Allow each coat a minimum of 30-45 minutes to level.
- After sealer levels, place fans in an adjacent area to pull moisture away from the job site. When each coat has dried a minimum of 2-3 hours (under good conditions), re-measure moisture content. If moisture content is not equal to the first reading, allow more dry time. Repeat for each coat.
- If necessary, abrade between coats to remove debris, hair, drips, etc. or if the 24-hour window between coats has elapsed. Abrade with the pad-and-strip system using 180-240 grit sanding strips. Between coats, vacuum and tack with a Basic Coatings Microfiber Mop dampened with Squeaky™.
- If the 24-hour window has elapsed, the TyKote® Dust-Free Refinishing System is an to alternative screening the floor. Refer to TyKote application procedures for details.
- Apply second coat in the same manner if desired
Painting Game Lines
Apply any painted game lines after screening and cleaning the second coat of sealer. Refer to gymnasium technical literature for acceptable paints and painting procedures.
Dry Time
Allow at least 2-3 hours between coats and 1 hour of good ventilation before closing job site.
Properties
- Color
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Solids Content | 26 - 30 | % | - |
| VOC | max. 275 | grams/liter | - |
| Dry Time | 2 - 3 | hours | - |
| Clean Up | Water | - | - |
| Coverage | 600.0 | sq. ft./Gallon | - |
| Flash Point | min. 200 | ºF | - |
| Freeze/Thaw Stability | Do not freeze | - | - |
Safety & Health
- Precaution
Keep out of reach of children. For industry use. Warning! Causes serious eye irritation. Causes skin irritation. Wear protective gloves: < 1 hour (breakthrough time): disposable vinyl. Wear eye or face protection: Recommended: safety glasses with side-shields. Wash hands thoroughly after handling. Keep closures tight and upright to prevent leakage. Keep container closed. In case of spillage, absorb and dispose of in accordance with local applicable regulations.
First Aid: If On Skin: Wash with plenty of soap and water. Take off contaminated clothing. Wash contaminated clothing before reuse. If skin irritation occurs: Get medical attention. If In Eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.
Packaging & Availability
- Packaging
- 1 U.S. (3.7 L) gallon container (4/case)
- 5 U.S. (18.9 L) gallon pail
- Availability
Waterbased Finish Sheen 1 Gallon 5 Gallon VOC Lock ‘N Seal™
- B0661-4312 B0661-0512 max. 275
Storage & Handling
- Storage
- Do not store above 120°F (49°C). KEEP FROM FREEZING
- Stability - 1 year shelf life under proper storage conditions.
- Do not store below 35° F (2°C).