Knowde Enhanced TDS
Identification & Functionality
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Raw Sealer Advantages
- Designed predominantly for White Oak
- Offers natural dry looking color
- Helps prevent tannin pull
- Wet sealer indicator: applies with slight hue for proper coverage which also prevents any missed spots
- Single component: Pre-catalyzed
- Can be used on any species to tone the wood color
- Fast Drying (2-3 Hours)
- Low VOC 275
Applications & Uses
- Markets
- Application Method
- Compatible Substrates & Surfaces
- Recommended Uses
Ideal for use in any residential or commercial wood flooring application. When applied as designed, it can be used with almost all species of hardwood flooring.
- Application
Read and understand technical data sheet and associated safety data sheet completely before beginning installations. Always use appropriate personal protective equipment. Prior to beginning a project, apply in an inconspicuous area to test and become familiar with your complete application method and to ensure product satisfaction. Follow industry standards and flooring manufacturer’s recommendation for acclimation, design, layout, and application of wood flooring materials.
Recommended Applicators
3/8” microfiber roller is preferred applicator. T-bar, roller, or paint pad can be used.
Recommended Systems
Full sand prior to use. To achieve a dry look or reduce tannin pull on white oak, apply 1 coat of Raw Sealer, followed by 2 coats of any clear Basic Coatings® waterbased finish. If a whiter tone or more tannin resistance is desired, add a second coat followed by 2 coats of any clear Basic Coatings waterbased finish. Raw Sealer may react differently depending on wood species. Prior to beginning a project, apply in an inconspicuous area to test and become familiar with your complete application method and to ensure product satisfaction.
Mixing
Rock container several times to thoroughly mix and re-disperse any settlement. Set aside for approximately 10 minutes to allow bubbles to break. It is important to stir from time to time to prevent settling.
Adding Water
Up to 12 ounces of water can be added per gallon of finish. Adding water will increase the flow and level time during situations of high temperature and low humidity.
Surface Preparation
Sand floors using accepted NWFA/MFMA procedures. Please Note: After final sanding, be sure to record moisture readings throughout installation. Moisture readings during installation provide a baseline/benchmark for when to begin next application steps. Always make sure moisture is within acceptable levels for region of the project. Thoroughly vacuum floor prior to application.
Sealer Application (Pre-application)
Always maintain adequate temperature/ventilation during all phases of the coating and drying process.
- Restrict air flow during application to help prevent premature drying.
- Measure moisture content of floor in several areas.
- Rinse applicator and remove all excess water. This also helps to remove loose fibers.
- Rinse refill applicator and remove all excess water. This also helps to remove loose fibers.
- Apply using a 3/8” microfiber roller, following standard water based application procedures.
- Allow a minimum of 30-45 minutes to level.
- After sealer levels, allow increased and balanced air movement and fresh air exchange. Proper air movement will help dry the sealer.
- After a minimum 2-3 hours (under good conditions), re-measure moisture content. If moisture content is not equal to the first reading, allow more dry time.
- If necessary, abrade between coats to remove debris, hair, drips, etc. or if the 24-hour window between coats has elapsed.
- Abrade with the pad-and-strip system using 180-240 grit sanding strips.
- Between coats, vacuum and tack with a Basic Coatings microfiber mop dampened with Squeaky™.
- If the 24-hour window has elapsed, the TyKote® Dust-Free
- Refinishing System is an alternative to screening the floor. Refer to TyKote application procedures for details.
- If desired, apply second coat in the same manner.
Important Tip: To help prevent tannin pull, assist in consistent color, and/or to address grain raise, do not abrade until after initial coat of finish.
Clean-up
This product can be cleaned with soap and water.
Dry/Cure Time
Allow at least 2-3 hours between coats and 1 hour of good ventilation before closing job site.
Coverage
Average of 450-550 sq.ft./gallon, depending on wood fl ooring species, porosity, and other jobsite conditions.
Precautions
KEEP OUT OF REACH OF CHILDREN. FOR INDUSTRY USE. WARNING ! MAY CAUSE AN ALLERGIC SKIN REACTION. Wear protective gloves. Avoid breathing vapor. Contaminated work clothing must not be allowed out of the workplace. FIRST AID: IF ON SKIN: Wash with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation or rash occurs: Get medical attention. Dispose of contents and container in accordance with all local, regional, national and international regulations.
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Solids Content | 29 - 31 | % | — |
| VOC | max. 275 | grams/liter | — |
| Flash Point | min. 200 | ºF | — |
| Freeze/Thaw Stability | Do not freeze | — | — |
| Dry Time | min. 2 - 3 | Hours | — |
| Clean Up | Water | — | — |
| Coverage | 450 - 550 | sq. ft./Gallon | — |
Packaging & Availability
- Packaging
- 1 US gallon plastic pail (4 per case)
Storage & Handling
- Storage
- Do not store below 35° F (2°C)
- Do not store above 120°F (49°C). KEEP FROM FREEZING.
- Stability - 1 year shelf life under proper storage conditions.
- Pot Life
1 year (unopened)