Products

BC 7136-2 is an aluminum filled thick section casting system with heat resistance to 300°F. May be cast to a thickness of 2 inches in non-conductive molds, 3 inches in conductive molds, and thicker sections with the addition of bulk fill. For service temperature above 150°F a post-cure is required. Does not contain VCHD or MDA. BC 7136-2 is recommended for uses such as: RTM and RIM molds, matched dies, injection and compression molds, and constructing vacuum form tools.BC 7136-2 can be removed from the mold after allowing to set 24 hours at room temperature (75°F). Post cure for applications requiring temperatures above 150°F can be accomplished in an oven or in use by a gradual heat rise; 2 hours @ 150°F, plus 2 hours @ 250°F, plus 2 hours @ 300°F.

BC 7069-1 is an aluminum filled, epoxy mass casting resin. This room temperature cure system may be cast to a thickness of ¾ inch in non-conductive molds and one inch in metal molds without foaming or yielding excessive shrinkage. Casting thickness can be increased by incorporating aluminum needles, puffs or granules. BC 7069-1 when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies.

BC 5008-2 is a very low viscosity, modified, unfilled, room temperature curing, general purpose resin system. Also considered an excellent general purpose adhesive for in-shop use and will function as a laminating system for horizontal surfaces.

BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.

BC 6126 is a gray, low toxicity, aluminum filled, epoxy surface coat. This thixotropic resin system provides excellent surface duplication along with vertical coverage to 1/16" thickness. This heat resistant system may be used at room temperature without post-curing. For use above 150°F a post-cure is required. Post cure for applications requiring temperatures above 150°F can be accomplished in an oven or in use by a gradual heat rise; 2 hours @ 150°F, plus 2 hours @ 250°F, plus 2 hours at 300°F. BC 6126 can afford consistent use to 300°F if required. BC 6126 was engineered to replace VCHD and MDA systems while retaining excellent heat resistance. Typical uses include constructing vacuum form tools, Injection and compression molds, RTM and RIM molds, and matched dies.

BC 7020 is a light weight two component epoxy backfill system. Unlike BC 7010, the filler portion is pre-blended into the resin and hardener components for easier handling, thus simplifying the mixing process. BC 7020 is ideally suited for foundry applications involving mold and core construction. BC 7020 features the following advantages: low cost, simple mix ratio (1 to 1 by wt.), long pot life, machinable, low shrinkage, color change to insure complete mix.Mixing Procedure:Combine equal parts (by weight) into a clean, dry mixing container such as a Hobart Kettle or similar vessel. Mix completely (5-10 minutes) until blue and yellow components yield a faint green uniform color. Empty mixture into mold cavity in 1 to 2 inch layers and compact (tamp) into place. NOTE: To insure adhesion between previously applied surface coat, laminate or BC 7020 backfill system, it is recommended that a thin layer of epoxy resin/hardener mixture be used prior to back filling with the BC 7020 system.

BC 5200 is a medium viscosity fast gelling two part Epoxy Adhesive System. With an easy to use 1 to 1 mix ratio, BC 5200 is considered an excellent general purpose adhesive for in-shop use. BC 5200 will bond to wood, concrete, select plastics, and most metal surfaces.Surface Preparation:Areas to be adhered to should be clean and dry, free of dust, oil, and release agents. It is advisable to scarify the surface with sand paper prior to application.Mixing Instructions:Combine 1 part of Resin to 1 part of Hardener by weight or by volume. Setting time is 4 to 4.5 minutes. May be applied by any reasonable thickness by spreading or splining. Do not work with more material than can be applied in 4 minutes. Surfaces should be held in position until cure is affected.p

BC 6128 is a black, non-staining, silicon carbide filled, "die surface" surfacing resin. This thixotropic resin system provides excellent surface duplication along with good vertical coverage. Extended mold life due to superior wear resistance and hardness are the major benefits derived from its use. This heat resistant system may be used at room temperature without post-curing. For use above 150°F a post-cure is required. Post cure for applications requiring temperatures above 250°F can be accomplished in an oven or in use by a gradual heat rise; 2 hours @ 150°F, plus 2 hours @ 250°F, plus 2 hours at 300°F. BC 6128 can afford consistent use to 300°F if required. Does not contain VCHD or MDA. Typical uses include constructing vacuum form tools, Injection and compression molds, RTM and RIM molds, and matched dies.

BC 5003 is a medium viscosity, unfilled laminating system. It is a room temperature curing resin with a relatively short pot life. BC 5003 is also considered an excellent general purpose adhesive for in-shop use. Recommended for use in gluing up BCC's Tooling Board Series.

BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.

BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.

BCC Resins HPX 691 is an Epoxy; Epoxide (Epoxy) product. It can be processed by casting and is available in North America. Typical application: Prototyping Applications.Characteristics include: Clarity Good Toughness Low Shrinkage Scratch Resistant

BC 5010 is a high quality, low viscosity room temperature curing laminating resin. A Safety System for the production of a variety if dimensionally stable fiberglass tools. BC 5010 features low odor and rapid "wet-out" with no vertical drain off. An excellent general purpose laminating resin to meet the tooling requirements for automotive, aircraft, and foundry.

BC 7136 is a gray, low toxicity, aluminum filled, epoxy casting resin. This heat resistant system may be used at room temperature without post-curing. May be cast to a thickness of ¾ inch in non-conductive molds. For use above 150°F a post-cure is required. Post cure for applications requiring temperatures above 150°F can be accomplished in an oven or in use by a gradual heat rise; 2 hours @ 150°F, plus 2 hours @ 250°F, plus 2 hours at 300°F. BC 7136 can afford consistent use to 300°F if required. This product was engineered to replace VCHD and MDA systems while retaining excellent heat resistance and low viscosity. Typical uses include constructing vacuum form tools, Injection and compression molds, RTM and RIM molds, and matched dies.

HPX-850 is a light weight, heat resistant, two component epoxy backfill system. Like BC 7020, the filler portion is pre-blended into the resin and hardener components for easier handling, thus simplifying the mixing process. HPX-850 features advantages such as low cost, long pot life, machineability, and low shrinkage. It is ideally suited for numerous applications involving mold and core constructions.HPX-850 can be removed from the mold after allowing to set 24 hours @ room temperature (75°F). Post cure for applications requiring temperatures above 150°F can be accomplished in an oven or in use by a gradual heat rise; 2 hours @ 150°F, plus 2 hours @ 250°F, plus 2 hours at 300°F.

BC 5105 is a clear, unfilled, low viscosity laminating system. This heat resistant resin exhibits excellent wet out, reasonable working time and may be used at room temperature without postcuring. For use above 150°F a post-cure is required. Post cure for applications requiring temperatures above 150°F can be accomplished in an oven or in use by a gradual heat rise; 2hours @ 150°F, plus 2 hours @ 250°F, plus 2 hours at 300°F. BC 5105 can afford consistent use to 300°F if required. Does not contain VCHD or MDA. Typical uses include constructing vacuum form tools, Injection and compression molds, RTM and RIM molds, and matched dies.

BC 6004 is a white thixotropic epoxy surface coat that had the ability to cure and bond to freshly poured wet plaster. This formulated resin compound can be applied with a brush or troweled to a thickness of 1/8" or less on vertical surfaces or over sharp radii without sag or fear of run-off. BC 6004 features moderate heat resistance and tracing hardness.Procedure for Plastic Faced Plaster Applications:BC 6004 should be applied over a properly mold-released surface so that positive removal of the surface coated plaster casting is assured. For best results, two coats approximately 1/16" thick should be used. The first coat should be brushed over the entire surface and then allowed to cure to a gelled or very tacky state. The second coat should be applied over the first. If hemp, glass or other fibrous plaster reinforcements are to be used, they should be placed in the freshly applied second coat immediately. Plaster can then be poured against the wet, second coat of BC 6004. To achieve good adhesion of the epoxy to the plaster, it is recommended that the plaster be poured immediately. The application of two coats of BC 6004 will eliminate surface porosity that sometimes occurs when fast setting, "hot" plaster compounds are cast over a single coat of epoxy.

BCC Resins BC 6060 is an Epoxy; Epoxide (Epoxy) product. It can be processed by casting and is available in North America. Typical application: Coating Applications. Primary characteristic: wear resistant.

BC5009 is a very low viscosity, modified, unfilled, room temperature curing, general purpose resin system.BC5009 is a clear-amber epoxy adhesive especially formulated for the bonding of wood and urethane model board. It may be also used as a laminating resin. The resin is color indicated (green) and will turn to a clear amber color as the hardener is mixed into the resin. This indicator system promotes fast and efficient mixing of the resin and hardener, insuring that they are thoroughly mixed yet wasting no time over mixing.

BC 5114 is a gray low viscosity laminating system. This heat resistant resin exhibits excellent wet out, reasonable working time and may be used at room temperature without postcuring. For use above 150°F a post-cure is required. Post cure for applications requiring temperatures above 150°F can be accomplished in an oven or in use by a gradual heat rise; 2hours @ 150°F, plus 2 hours @ 250°F, plus 2 hours at 300°F. BC 5105 can afford consistent use to 300°F if required. Does not contain VCHD or MDA. Typical uses include constructing vacuum form tools, Injection and compression molds, RTM and RIM molds, and matched dies.

BCC Products EB6200 is a "grain-free" elevated temperature epoxy modeling material known for its superior surface finish, dimensional stability and the ability to maintain tolerances even after being subjected to temperature variations. EB6200 has excellent dimensional stability results from the low coefficient of thermal expansion and high glass transition temperature.ApplicationsMaster Models (Aerospace); Automotive Die Models; Vacuum Forming at Elevated Temperatures; Lay-Up Tools for Medium and High Temperature Curing Prepreg

BC 7053 is an iron filled epoxy casting system. This system is a high iron content material that provides unsurpassed wear resistance. BC7053 was designed for use in constructing core boxes, holding and trimming fixtures, foundry patterns, etc.

BC 7009-2 is an iron filled, low-cost mass casting system. Recommended for use in casting a minimum of two inches and a maximum of six inches in non-conductive molds. Thicknesses to nine inches in metal or conductive-type molds can be successfully achieved as well. Ideal for stretch forms, patterns, dies, molds, duplications, prototypes, etc.

BC 6005 is a snow white thixotropic epoxy resin designed specifically for quality reproduction of a variety of surfaces. A room temperature cure system that offers ample working time yet affords quick-tack for lamination. BC 6005 may be applied easily with a brush or troweled to a thickness of 1/8" or less on vertical surfaces or over sharp radii without sag or fear of run-off. When cured, this resin system provides a hard tough chip-resistant surface.

BC 7009-1 is an iron oxide filled, low-cost mass casting system. Thicknesses up to two inches in non-conductive molds, and four inches in conductive molds can be achieved without foaming or yielding excessive shrinkage. Ideal for stretch forms, patterns, dies, molds, duplications, prototypes, etc.

BC 7062 are aluminum filled, low viscosity epoxy mass casting resins. These room temperature cure systems allow the user choice thicknesses of 1/8 inch to a maximum of 6 inches without foaming or yielding excessive shrinkage. Casting thicknesses may be increased by incorporating aluminum needles, puffs or granules. BC 7062, when properly cured, provides nearly perfect reproduction, resulting in a dimensionally stable, hard, tough surface. For use in constructing duplicate models, prototypes, patterns, facing dies, etc.

BE 290 is a low viscosity, medium pot life, room temperature laminating system. BE 290 features low odor, reduced toxicity and adequate working life for construction medium and large fabricating tools.