Belzona 2131 FN10181

Identification & Functionality

Product Type

2K (2 component) Coating

Technologies

Ready-to-Use Products

Product Families

Ready-to-Use Products — Paints & Coatings

Protective Coatings

Features & Benefits

Ready-to-Use Product Features

Abrasion Resistant,

Chemical Resistant,

Corrosion Resistant,

Durable,

Excellent Mechanical Strength,

Impact Resistance,

Wear Resistant

Applications & Uses

Markets

Industrial,

Paints & Coatings

Applications

Industrial — Chemical & Industrial Manufacturing

Equipment & Parts

Paints & Coatings — Industrial Coatings

Industrial Coatings

Application Area

Bearings,

Vacuum Pumps

Application Method

Brush

Application Areas

When mixed and applied as detailed in the Belzona Instructions for Use (IFU), the system is ideally suited for application to the following:

• Surfacing pumps
• Repairing diaphragms
• Replacing drive couplings
• Casting flexible molds
• Casting shock absorbers
• Casting guide bearings

Application Information

Application Methods

• Applicator
• Spatula
• Brush
• Pouring

Working Life - The working life will vary according to temperature. At 68°F/20°C the usable life of mixed material will typically be 12 minutes. Consult the Belzona IFU for specific details.

Cure Time - Cure times will vary depending on ambient conditions; consult the Belzona IFU for specific details.

Volume Capacity - The volume capacity of mixed material will be 886cm³/kg, 443cm³ per 500g unit.

Base Component

Appearance	Pale straw colored viscous liquid
Density	11-1.2 g/cm3
Viscosity	190-330 P at 77°F/25°C

 

Solidifier Component

Appearance	Thin black liquid
Density	1.06 g/cm3
Viscosity	11 P at 77°F/25°C

 

Mixed Properties

Appearance	Black liquid
Density	1.13 g/cm3
Sag Resistance	10mil/250nm maximum
VOC content (ASTM D2369/EPA ref 24)	0.25% / 2.85 g/L

 

Mix Ratio (base:solidifier)

Mixing Ratio by Weight (Base : Solidifier)	3.4:1
Mixing Ratio by Volume (Base : Solidifier)	3.2:1

Properties

Typical Properties

	Value	Units	Test Method / Conditions
Dry Abrasion (7 day cure, 68°F[20°C])	30.0	mm3 loss per 1000 cycles	ASTM D4060
Elongation (24 hours, 68°F[20°C])	500 - 600	%	—
Elongation (7 days, 68°F[20°C])	400 - 500	%	—
Hardness (24 hours, 68°F[20°C])	90.0	Shore A	ASTM D2240
Hardness (7 day, 68°F[20°C])	93.0	Shore A	ASTM D2240
Tear Strength (24 hour and 7 day, 68°F[20°C])	385 (6875)	pli (kg/m)	ASTM D624
Tensile Modulus (24 hours, 68°F[20°C]).	215 (1.5)	psi (MPa)	—
Tensile Modulus (7 day, 68°F[20°C])	205 (1.4)	psi (MPa)	—
Tensile Strength (24 hours, 68°F[20°C]).	2460 (17)	psi (MPa)	—
Tensile Strength (7 day, 68°F[20°C])	2280 (15.7)	psi (MPa)	—
Wet Abrasion (7 day, 68°F[20°C])	30.0	mm3 loss per 1000 cycles	ASTM D4060

Electrical Properties

	Value	Units	Test Method / Conditions
Dielectric Constant (1.0 V, 100 Hz)	5.02	—	ASTM D150
Dielectric Strength (500 V/s)	7.1	kV/mm	ASTM D149
Dissipation Factor (1.0 V, 100 Hz)	0.021	—	ASTM D150
Surface Resistivity (500 V DC)	7.66 x 10^12	ohm	ASTM D257
Volume Resistivity (500 V DC)	2.30 x 10^12	ohm	ASTM D257

Technical Details & Test Data

Adhesion

90° Peel Adhesion
When tested in accordance with ASTM D429 (modified), typical adhesion values achieved when the material is used in conjunction with the designated surface and recommended surface conditioner will be:

Substrate	Peak Adhesion	Failure Mode
Grit Blasted Mild Steel	186 pli 3320 kg/m	Tape Failure

180° Peel Adhesion
When tested in accordance with ASTM D413, typical adhesion values achieved when the material is used in conjunction with the designated surface and recommended surface conditioner will be:

Substrate	Peak Adhesion	Average Peel Adhesion	Failure Mode
EPDM (Shore A: 75)	20 pli 350 kg/m	5 pli 90 kg/m	Cohesive in Substrate
Nitrile (Shore A: 77)	37 pli 655 kg/m	21 pili 375 kg/m	Cohesive in Substrate
Neoprene (Shore A: 83)	28 pili 510 kg/m	13 pli 230 kg/m	Cohesive in Substrate
Natural Rubber (Shore A: 51)	14 pli 250 kg/m	4 pli 65 kg/m	Cohesive in Substrate
Commercial Rubber (Natural/SBR) (Shore A: 72)	14 pli 255 kg/m	9 pli 160 kg/m	Cohesive in Substrate
Insertion Rubber (commercial with textile reinforcement) (Shore A: 70)	21 pli 375 kg/m	9 pli 155 kg/m	Cohesive in Substrate

 

Chemical Resistance

Once fully cured, the material will demonstrate excellent resistance to a range of chemicals including; dilute inorganic acids and alkalis.

Compression Resistance

When tested in accordance with BS 903 part A6, the compression set following a 30 minute recovery period will typically be 24%.

Heat Resistance

Dry - For many typical applications the product will be suitable for operation in dry conditions in the temperature range -40°F to 194°F (-40°C to 90°C).

Wet - For wet or immersed conditions the maximum service temperature is 104°F (40°C).

Storage & Handling

Shelf Life

Separate base and solidifier components shall have a shelf life of 3 years from date of manufacture when stored in their original unopened containers between 41°F (5°C) and 86°F (30°C).