Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Humiseal 1R32 LTX has the following advantages:
- Protection against moisture, salt / corrosive environments and dirt.
- Easy application with automated systems.
- Easy to cure and dry.
- Low odor in use.
- Low moisture vapor permeability.
- Fluoresces under UV for ease of inspection and is easily repaired.
- Easy removal using Humiseal® Strippers.
- Range of preblends thinners available for different application methods
- Compliant with GB30981-2020*
Applications & Uses
- Markets
- Application Area
- Coating Type
- Application
Conformal coatings can be successfully applied to substrates that have been cleaned prior to coating and also to substrates assembled with low residue “no clean” materials. Users should perform adequate testing to confirm compatibility between the conformal coating and their particular assembly materials, process conditions and cleanliness level. Please contact HumiSeal® for additional information.
HumiSeal® 1R32 LTX Pre-Blends are specifically diluted to a viscosity for immediate use. No additional dilution is required. Customers should establish which Pre-Blend is suitable for their equipment and application method before commercial use. HumiSeal® Technical Support should be contacted if any further advice on Pre-Blends and equipment is required.
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Viscosity | 200 ± 15 | cPs | - |
| Solids | 35 ± 3 | % | - |
| Density | 0.91 ± 0.02 | g/cm³ | - |
| VOC | 592.0 | grams/litre | - |
| Recommended Coating Thickness | 25 - 75 | microns | - |
| Drying Time to Handle (per Fed-Std-141, Meth. 4061) | 10.0 | minutes | - |
| Recommended Curing Conditions | 24 hrs @ RT or 30 min @ 76°C | - | - |
| Time Required to Reach Optimum Properties | 7.0 | days | - |
| Recommended Stripper | HumiSeal® Stripper 1080 | - | - |
| Thermal Shock ( 50 cycles per MIL-I-46058C) | -65 - 125 | °C | - |
| Coefficient of Thermal Expansion - TMA | 170.0 | ppm/°C | - |
| Coefficient of Thermal Expansion - TMA (above Tg) | 340.0 | ppm/°C | - |
| Glass Transition Temperature - DSC | 14.0 | °C | - |
| Modulus - DMA (-40°C) | 2000.0 | MPa | - |
| Modulus - DMA (20°C) | 1050.0 | MPa | - |
| Modulus - DMA (60°C) | 8.5 | MPa | - |
| Dielectric Withstand Voltage ( MIL-I-46058C) | min. 1500 | volts | - |
| Dielectric Breakdown Voltage | 7500.0 | volts | ASTM D149 |
| Dielectric Constant ( 1MHz and 25°C ) | 2.5 | - | ASTM D150-98 |
| Dissipation Factor ( 1MHz and 25°C ) | 0.01 | ASTM D150-98 | - |
| Insulation Resistance (per MIL-I-46058C ) | 8.0 x 1014 (800TΩ) | ohms | - |
| Moisture Insulation Resistance, per MIL-I-46058C | 6.0 x 1010 (60GΩ) | ohms | - |
| Fungus Resistance | Passes | ASTM G21 | - |
Regulatory & Compliance
- Certifications & Compliance
Safety & Health
- Caution
Application of HumiSeal® Conformal Coatings should be carried out in accordance with local and National Health and Safety regulations.
The solvents in HumiSeal® Conformal Coatings are flammable. Material should not be used in presence of open flame or sparks. Use only in well-ventilated areas to avoid inhalation of vapors or spray. Avoid contact with skin and eyes.
Packaging & Availability
- Availability
Humiseal 1R32 LTX is available in a range of pre-blends, which are formulated for use with no further dilution:
- Pre-blends with Thinner 600 are ideal for enhanced spray application
- Pre-blends with Thinner 789 are ideal for film coater systems. Heated systems may be needed for 120CPS pre-blends, providing improved coating coverage
Storage & Handling
- Storage
HumiSeal® 1R32 LTX and Pre-Blends should be stored away from excessive heat or cold, in tightly closed containers. HumiSeal® products may be stored at temperatures of 0 to 35°C. Prior to use, allow the product to equilibrate for 24 hours at a room temperature of 18 to 32°C.