Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
Features & Benefits
- Ready-to-Use Product Features
- Advantages
- Crystal Clear-A is much tougher than traditional acrylic sealers. The high gloss created by Crystal Clear-A lasts up to 70% longer.
- Crystal Clear-A completely resists discoloration from ultraviolet light exposure.
- Crystal Clear-A cures concrete to ASTM C1315 standards to minimize cracking and increase the strength of concrete.
- Protects surfaces against deicing chemicals, fertilizers, salts, grease, oil, alkalies, mild acids and detergents.
Applications & Uses
- Markets
- Compatible Substrates & Surfaces
- Uses
- Cure freshly poured exterior plain, colored, stamped or exposed aggregate concrete to ASTM 1315 where superior curing efficiency is required.
- Seal, harden, and dustproof existing concrete particularly architectural or residential concrete exposed to freeze-thaw or ultra violet light.
- Enhance the color and gloss of pigmented or stamped concrete.
- Directions for Use
Mixing: Clear Crystal Clear-A is packaged ready to use. Do not dilute.
Surface Preparation: If using to cure fresh concrete, apply as soon as all bleed water has dissipated. If applying as a sealer for older concrete, clean thoroughly with high-pressure water and allow the concrete to thoroughly dry.
Application: Apply uniformly leaving no pinholes or gaps. Do not allow the material to puddle.
Spray Apply with a low pressure, solvent resistant, airless, sprayer equipped with a fan nozzle orifice of 0.030 to 0.035” at 1 gpm. The optimum spray pattern is an 8” to 12” fan. Hold sprayer tip 8” to 12” from the surface of the concrete.
Roller Apply: Use a short nap (1/4” max) solvent resistant roller.
Application Rate:
Curing: 300 ft2/gal (7 m2/L)
Sealer: 350 to 450 ft2/gal (9 to 11 m2/L). Unsealed concrete may require an optional second coat.
Clean-up: Clean tools with solvent such as xylene immedi-ately after use.
Regulatory & Compliance
- Certifications & Compliance
- Standard Specification
- ASTM C1315, Type I Class A, (upon request ID & II) Standard Specification for Liquid Membrane-Forming Compounds for Curing and Sealing Concrete
- ASTM C309, Type 1, Class A & B (upon request 1D & 2) Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete
- AASHTO M-148, Type 1, Class A & B (upon request 1D & 2) Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete.
- Complies with National V.O.C. Emission Standards for Architectural Coatings, Federal EPA Regulation 40 CFR Part 59 and lower V.O.C. regulations @ < 700 g/L
- Meets USDA requirements for incidental food contact when fully cured
- Version to meet U.S. Army Corps of Engineers CRD-C-300 available upon request.
Technical Details & Test Data
- Limitations
- Not for use indoors.
- Strong organic solvents will soften and lift Crystal Clear-A
- Do not use at temperatures below 40°F (4°C)
- Do not use where solvent odor may be a problem
- Application will darken concrete
- Uneven application may cause blotchiness
- Shelf life is two years from date of manufacture
- Technical Data
Physical Properties ASTM C156 Moisture Retention 0.035 g/cm2 PMCC Flash point °F (°C) 1 (-17) V.O.C. Content <350 g/L Drying Time @ 70°F (21°C)
Tack Free
Light foot traffic
Maximum hardness2 hours
8 hours
7 daysYellowing Index
1,000 QUV Exposure, Simulates approximately
10 yrs of Florida Sunlight.
Visible yellowing begins at 3.0 IndexProduct Yellowing E.O.T. Initial Rating All Products 0 Crystal Clear-A 0 Moisture Cure Urethane 3 Pure Acrylic 4.77 Styrene Acrylic 9.48 Gloss Retention
1,000 hours QUV Exposure
All panels begin with Gloss Rating = 95Product Gloss Rating E.O.T. % of Initial Crystal Clear-A 89.8 95 Moisture Cure Urethane 79.1 83 Pure Acrylic 73.6 77 Styrene Acrylic 55.4 58 Estimating Guide
coverage rates vary with concrete conditionft2/gallon m2/liter Curing 300 7 Sealing/dustproof 350 8 Optional 2nd Coat 450 11
Packaging & Availability
- Packaging
Packaging Product Number 5 gal (18.9 liter) 36 per pallet F1337.05 55 gal (208 liter) 4 per pallet F1337.55
Storage & Handling
- Storage
Store tightly sealed containers in cool, dry area away from direct sunlight and sources of heat. Shelf life is two years from date of manufacture. Store locked up.
- Disposal
Dispose of contents/container in accordance with local, regional, and national regulations.