Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
- Limitations
- If a uniform color is desired Classic FX or Acid stain is recommended
- Will not hide moving cracks however, adds to their character
- Must be installed over a clean dry surface
- Moisture & efflorescence must be removed with Classic Densifier for a clean dry surface.
- All surfaces must be cleaned with Super Eco-Etch, power washed & rinsed well with water
- Coverage
Coverage rates will vary Significantly from floor to floor based on the roughness or texture of the concrete, porosity and the mix design. Expect approximately 400 to 600 sq. ft. per 1.5 gal.
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
It's cutting edge technology allows greater penetration because it has the smallest particle size available in a concrete stain. It is ideal for interior or exterior use as it is UV protected and will not fade in the sun. You can also achieve a mottled look similar to acid or dye stain. Nano-Infused can be sealed two hours after application with a Classic Coatings Systems water base or solvent sealer. Application is easiest with a pump sprayer with a conical tip attached. Tip size of .05 to .15 gpm at 30-40 psi is recommended to reach coverage rates of 400-600 sq. ft. per gallon. Nano-Infused is packaged as a liquid concentrate.
Applications & Uses
- Markets
- Applications
- Applications
Mist the concrete with water then apply a very light application of stain. The more stain that you apply the darker the color gets. To eliminate any brush strokes in the stain, mist very little water over the brush strokes unless the strokes are desired in the finish. When the stain dries, spray a second coat on top for a darker color and more solid base. For a more diffused look, you may wish to spray the stain onto the surface without brushing. Every slab of concrete is different and staining is an artistic process so when available do small test patch on the surface corners so you can get the look that you like the best. Water based stains can not be cut with water to lighten the colors shade because it will not bond to the surface. The best option is to test a small area of the concrete using full strength. Cement content and weathering is another reason to do as many sample tests as the job site will allow. Let the stain dry and processes. Different stains need different times to activate and fully color the concrete (generally 15 minutes to 1 hour). Be sure and check your stains activation time before starting the job to insure full coloring of the surface. If you are going for the most color from a given stain, spray another coat of stain over the dried surface. Do not walk on wet surfaces since the stain is active and can retain impressions of your feet or other marks from tools.
- Uses
Classic Nano-Infused Concrete Stain can be used anywhere architectural concrete is desired. Both interior and exterior, on almost any cementitious surface, whether it be gray or color harden concrete, stamped or textured concrete, micro-toppings or overlays. It can be used as an entire surface colorant or just as an accent border or detail. It may be used on both new and existing substrates. Typically used as flooring in restaurants and food service areas, bars, hotels, casino’s, retail stores, malls, art studios, movie theaters, museums, pool decks, automobile showrooms, residential flooring and more. Classic Stain may also be used as a means to color poured in place concrete; both smooth or with a form linear, tilt up wall, stone-face plaster, GFRC and faux rock.
- Advantages
- Protects and preserves the effect against wear and exposure when sealed
- Multiple colors can be used for more interesting images
- Complies with all applicable air quality management regulations – Zero VOC
- All colors can be used interior and exterior Compared to acid stain there’s no fumes.
- No neutralization required and Non-hazardous shipping
- Low cost, easy install & low maintenance
Safety & Health
- Safety
- Highly Recommended To Test A Small Inconspicuous Area First.
- Turn Off Sprinklers For Two Days Prior To And After.
- Always Protect Neighboring Surfaces Including Wood,
- Carpet, Metal, Landscaping And Other Non-masonry Surfaces.
- Caution: Surface Is Slippery When Wet.
- New Concrete Must Cure For 28 Days Before Sealer Is Apply.
Packaging & Availability
- Packaging
- 1 quart makes 1.25 gallons when mixed with 1 gal. Acetone or water.
- 1 gallon makes 5 gallons when mixed
Storage & Handling
- Storage
- Store in a cool, dry location.
- Store out of direct sunlight.
- Protect pails and jugs from weather and other damage.
- Store at a temperature between 40°F (4°C) and 90°F (32°C).