Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
- Coverage
1 gallon (3.8 Liters) covers approximately 350sq.ft. to 500 sq.ft. Note: do not dilute. One light coat ill yield greater results.
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
This advanced formula allows color to reach full potential almost immediately upon application. Color may be built up without the worry of damaging the concrete as with acid stain. Numerous coats can be applied instantly, no need to apply them for an extended period of time. All colors may be used interior and exterior in a wide range of environments. Apply Classic Coatings Systems Sealer over the stain to make it pop & become more vibrant. It is highly recommended to test a sample area first. If using more than one gallon of the same color, mix them together then apply to your surface for even distribution of color.
Applications & Uses
- Markets
- Applications
- Applications
- Mist the concrete with water then apply a very light application of stain. The more stain that you apply the darker the color gets. To eliminate any brush strokes in the stain mist very little water over the brush strokes unless the strokes are desired in the finish.
- When the stain dries, spray a second coat on top for a darker color and more of a solid base. For a more diffuse look, you may wish to spray the stain onto the surface without brushing.
- Every slab of concrete is different, and staining is an artistic process so when available do small test patches on the surface corners so you can get the look that you like the best. Waterbased stains can not be cut with water thus making color lighter in shade because it will not bond to the surface. The best option is to test a small area of the concrete using full strength.
- Cement content and weathering is another reason to do as many pre-stain tests as the job site will allow. Let the stain dry and processes. Different stains need different times to activate and fully color the concrete (generally 15 minutes to 1 hour). Be sure and check your stains activation time before starting the job to insure full coloring of the surface. If you are going for the most color from a giving stain, spray another coat of stain over the dried surfaces. Do not walk on the wet surfaces, the stain is active and can retain impressions of your feet or other marks from your tools.
- Uses
Classic Simple Stain can be used anywhere architectural concrete is desired. Both interior and exterior, on almost any cementitious surface, whether it be gray or color harden concrete, stamped or textured concrete, micro-toppings or overlays. It can be used as an entire surface colorant or just as an accent border or detail. It may be used on both new and existing substrates. Typically used as flooring in restaurants and food service areas, bars, hotels, casino’s, retail stores, malls, art studios, movie theaters, museums, pool decks, automobile showrooms, residential flooring and more. Classic Stains may also be used as a means to color poured in place concrete; both smooth or with a form linear, tilt up wall, stone-face plaster, GFRC and faux rock.
- Advantages
- Protects and preserves against wear and exposure when sealed
- Multiple colors can be used for more interesting images
- Semi-transparent highs and lows
- Most colors can be used interior and exterior
- UV stable and Zero VOC Low cost, easy install & low maintenance
- No neutralization required and Non-hazardous shipping
- Limitations
- If a uniform color is desired, Classic CDC line is recommended
- Not for use on self-leveling cement or light weight concrete.
- We recommend Classic FX2, Acid Stain, or Nano-Infused Dye.
- Must be installed over a clean dry surface.
- Surface should feel like it is under 100 grit sandpaper.
- Moisture & efflorescence must be removed with Classic Densifier for a clean dry surface.
- Clean surfaces with Super Eco-Etch, power wash & rinsed well.
- Not recommended for use on polished or hard troweled, smooth finish concrete.
- Never apply adhesives over stained or sealed surfaces.
- May cause damage.
Safety & Health
- Safety
- Highly Recommended To Test A Small Inconspicuous Area First.
- Turn Off Sprinklers For Two Days Prior To And After.
- Always Protect Neighboring Surfaces Including Wood,
- Carpet, Metal, Landscaping And Other Non-masonry Surfaces.
- Caution: Surface Is Slippery When Wet.
- New Concrete Must Cure For 28 Days Before Sealer Is Apply.
Packaging & Availability
- Packaging Type
- Packaging
Available in 1 gallon jugs, 5 gallon pails and 55 gallon drums.
Storage & Handling
- Shelf Life
- 3 (years)
- Storage
- Store in a cool,dry location.
- Store out of direct sunlight.
- Protect pails and jugsfrom weather andother damage.
- Store at a temperaturebetween 40°F (4°C) and 90°F (32°C).