Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- Coverage
1 gallon (3.8 Liters) covers approximately 400sq. ft. to 700 sq.ft. depending on application and surface. Note: do not dilute.
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
Considerable variations in color and tone normally result from the use of Classic Stain. Many special color effects may be achieved using different application techniques. Classic Nano-Hybrid stain provides a natural art deco look over old and new surfaces, interior, and exterior. It is an environmentally friendly alternative to acid stains. If using more than one gallon of the same color, mix them together in a 5 gallon pail then apply to your surface for even distribution of color. Shake very well as pigment may settle at the
bottom of the gallon.
Applications & Uses
- Markets
- Applications
- Applications
Mist the concrete with water (only if surface is hot) then apply a very light application of stain. The more stain that you apply the darker the color gets. To eliminate any brush strokes in the stain mist very little water over the brush strokes unless the strokes are desired in the finish. When the stain dries, spray a second coat on top for a darker, more solid base. For a more diffused look, you may wish to spray the stain onto the surface without brushing. Every slab of concrete is different, and staining is an artistic process so when available do small test patches on the surface corners so you can get the look that you like the best. Waterbased stains can not be cut with water thus making color lighter in shade because it will not bond to the surface. The best option is to test a small area of the concrete using full strength. Cement content and weathering is another reason to do as many pre-stain tests as the job site will allow. Let the stain dry and process. Different stains need different times to activate and fully color the concrete (generally 15 minutes to 1 hour). Be sure and check your stains activation time before starting the job to insure full coloring of the surface. If you are going for the most color from a given stain, spray another coat of stain over the dried surface. Do not walk on the wet surfaces, the stain is active and can retain impressions of your feet or other marks from your tools.
- Uses
Classic Water Based Stain can be used anywhere architectural concrete is desired. Both interior and exterior, on almost any cementitious surface, whether it be gray or color harden concrete, stamped or textured concrete, micro-toppings or overlays. It can be used as an entire surface colorant or just as an accent border or detail. It may be used on both new and existing substrates. Typically used as flooring in restaurants and food service areas, bars, hotels, casino’s, retail stores, malls, art studios, movie theaters, museums, pool decks, automobile showrooms, residential flooring and more. Classic Stain may also be used as a means to color poured in place concrete; both smooth or with a form linear, tilt up wall, stoneface plaster, GFRC and faux rock.
- Advantages
- Protects and preserves against wear and exposure when sealed
- Multiple colors can be used for more interesting finishes
- Complies with all applicable air quality management regulations – Zero VOC
- All colors can be used interior and exterior Compared to acid stain there’s no fumes.
- No neutralization required and Non-hazardous shipping
- Low cost, easy install & low maintenance
- Limitations
- If a semi-transparent finish is desired, Classic FX Nano is recommended
- Not for use on self-leveling cement or light weight concrete.
- We recommend Classic FX2, Acid Stain, or Nano-Infused Dye.
- Must be installed over a clean dry surface.
- After sealing, let cure for 5 days before parking on it.
- Moisture & efflorescence must be removed with Classic Densifier for a clean dry surface.
- All surfaces must be cleaned with Super EcoEtch, power washed & rinsed well with water.
- Surface should feel like it is under 100 grit sandpaper.
- Never apply adhesives over stained or sealed surfaces.
- May cause damage.
Properties
Safety & Health
- Safety
- Highly Recommended To Test A Small Inconspicuous Area First.
- Turn Off Sprinklers For Two Days Prior To And After.
- Always Protect Neighboring Surfaces Including Wood,
- Carpet, Metal, Landscaping And Other Non-masonry Surfaces.
- Caution: Surface Is Slippery When Wet.
- New Concrete Must Cure For 28 Days Before Sealer Is Apply.
Packaging & Availability
- Packaging
Available in 1 gallon jugs, 5 gallon pails and 55 gallon drums.
Storage & Handling
- Shelf Life
- 3 (years)
- Storage
- Store in a cool, dry location.
- Store out of direct sunlight.
- Protect pails and jugs from weather and other damage.
- Store at a temperature between 40°F (4°C) and 90°F (32°C).