Knowde Enhanced TDS
Identification & Functionality
- Carrier
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Benefits
- Gives paving stones a color enhancing wet look in a gloss finish
- Protects against penetration of moisture, deicing salts, oil, grease and dirt
- Will not yellow on exterior exposure
- Available in gloss and anti-slip finish of
- Meets the requirement of OTC (V.O.C. meets the requirements <350gms/L)
Applications & Uses
- Applications
- Application Method
- Compatible Substrates & Surfaces
- Used in
- As a sealer for colored or plain stamped concrete, interlocking pavers on sidewalks, driveways, and both residential and commercial patios
- As a sealer for both horizontal and vertical exterior concrete surfaces
- As a sealer for concrete floors in factories and warehouses
- Surface Preparation
- The ideal surface is a clean new surface
- CIPADECK® Paver & Concrete Sealer should be applied directly after the paving stones are installed, cleaned and allowed to dry completely or the concrete surface is dry
- Previously installed paving stones or existing concrete surfaces must be clean and dry, free from all grease, oil, laitence and any other foreign matter. If doubt exists as to the condition of the surface, chemical cleaning is recommended
- Under no conditions should paving stones or concrete surfaces be cleaned by sand blasting
- Application
- Do not dilute with any solvent, Apply as is
- CIPADECK® Paver & Concrete Sealer must be applied by low pressure sprayer
- The sprayer must be resistant to acetone solvent (Chapin X-treme™ sprayer or equivalent equipped with a fan tipped nozzle rated 1 gal./min.)
- Roller application is not recommended
- A light second coat may be required for uniformity in some cases
- Allow the first coat to dry for 24 hours prior to application of second coat
- Do not over apply the second coat
- This sealer is packaged in white pails to avoid heating in warm weather
- Solvents contained in this sealer are very flammable
- Prior to application over previously applied sealers always test to ensure compatibility
- Limitations
- CIPADECK® Paver & Concrete Sealer is not recommended for:
- Application to damp or wet surfaces
- interior applications of occupied buildings
- Application as a chemical resistant coating
- Areas where solvent exposure is a service condition
- Application to carbonated concrete
- Application in direct sunlight
- Application in extreme temperatures
- Application during high winds
- Application below 5°C (40°F) for best results condition material to 10°C(50°F) prior to application
- Coverage
First Coat - 4.9m²/L - 7.4m²/L (200-300ft/U.S. gal) depending on porosity and surface texture
Optional Second Coat - 7.4m²/L - 9.8m²/L (300-400ft/U.S. gal)- Clean up
Clean equipment with CPD Xylol immediately after application.
Regulatory & Compliance
- Certifications & Compliance
- Certifications
- Complies with National Organic Compounds Emission Standards for Architectural Coatings, Federal EPA Regulations 40 CFR Part 59
- Complies with the Ozone Transport Commission Volatile Organic Compound Emission Standards effective September 8th, 2010. The V.O.C. content is <350gms/L
Packaging & Availability
- Packaging
205L (55 US gal) drum/218 kg (480 lbs)
18.9L (5 US gal) pail / 19.5 kg (43 lbs)
3.79L (1U.S.gal) can 3.5Kg (7.7lbs) can
Storage & Handling
- Storage
- Store product indoors away from heaters, open flame or any other ignition sources
- Keep containers closed when not using product
- Freezing will not affect product but temperature of product before use must be 10°C (50°F) minimum prior to using
- Shelf Life
Two years from the date of manufacture when stored in original unopened container under normal warehouse conditions.