Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Components (75°C)
- 1
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features & Benefits
Ultraroof Works Great Over
- Mineral surface modifiedbitumen
- Smooth surface modifiedbitumen
- Smooth surface built-uproof
- Mineral surface built-uproof
- Granulated asphalticsurfaces
- Hot-mopped asphaltcut-back
- Emulsion tar and gravel
- Metal and galvanized
Benefits
- Ultraroof 900 was designed as a single part water based coating with the highest performance in coastal, temperate, humid, hot, and extreme alkaline environments. Ultraroof 900 creates a tough, long-lasting protective membrane that remains flexible over time, even under adverse conditions. Its elongation and tensile strength provide unsurpassed resistance to maintenance traffic, weather conditions, and wear.
- Unlike similar generic coatings, Ultraroof 900 is formulated to have exceptional adhesion to a variety of substrates. Its proprietary formula features copolymer elastomeric resins to produce a seamless, flexible, durable membrane that displays exceptional weathering ability and good UV resistance.Ultraroof 900 offers superior waterproofing but still breathes enough to allow trapped moisture vapor to pass through the film, while remaining impervious to exterior water penetration.
- Due to its light weight, the system can be applied over existing roofs without having to tear them off. Ultraroof 900 has better coverage and waterproofs better than the same amount of acrylic or asphalt. During spray application, the coating cures quickly allowing faster job completion.
- Ultraroof 900 creates superior waterproofing, forming a vapor barrier at 0.6 perms. This is more than 3 times better than asphalt, and 10 times better than acrylics. The coating will minimize problems in ponded areas. Also, Ultraroof 900 has tenacious adhesion to the substrate, and sticks like an epoxy glue. Unlike asphalt coatings, Ultraroof is UV resistant, alkali/salt resistant, and microbial resistant.
Save Money
- Light Weight-Install Over the Existing Roof
- Restores Existing Roof-Avoid a Costly Tear-off
- Blocks UV-Stop Roof Deterioration
- Cures Fast-Complete the Job Faster
- More Coverage- Waterproof at the Lowest Cost
- Considered Maintenance-Write-Of Coating This Year
Due to its light weight, the system can be applied over existing roofs without having to tear them of. Acrylastic 900 has better coverage and waterproofs better than the same amount of acrylic or asphalt. During the spray application, the 900 cures quickly allowing faster job completion.
Extend Roof's Waterproofing Life
- Tenacious Adhesion Stick Firmly to the Roof
- High Tensile StrengthPrevent Breaking
- Low Perm Rate Keep Liquid Out
- Breathes-Let Water Vapor Pass
- Resists Alkali-Apply in Low-pH Environment
- Resists Acid-Withstand Acidic Rain
- Resists Salts-Apply Near the Ocean
Acrylastic 900 creates superior waterproofing, forming a vapor barrier at O.6 perms. This is more than 3 times better than asphalt, and 10 times better than acrylics. The 900 will minimize problems in ponded areas. Also, the 900 has tenacious adhesion to the substrate, and sticks like an epoxy glue. Unlike asphalt coatings, Acrylastic 900 is UV resistant. It also resists alkalilsalt, to extremes of pH of 13, and is highly resistant to acid.
Protect the Environment
- Few Anti-microbial Additives-Keep Runoff Clean
- No Solvents, Low VOC-Avoid Harmful Fumes
- Non-Toxic-Preserve Building Health
Acrylastic 900 is water-based for easy cleanup and low odor. It contains low VOCs to keep the air healthier for people to breathe. Because of the low perm rate and smooth top coats, Acrylastic systems require few anti-microbial agents. Also, Davlin products contain NO zinc additives and have a low erosion rate, which contributes to cleaner waste-water in our streams, rivers, lakes, and bays.
Acrylastic™ UltraRoof™ 900 is one of
- Ultraroof 900 Primer
- Acrylastic 510 Roof Coating
- Roofseal Acrylic Elastomeric RoofCoating
- Roofseal Tropical Roof Coating
- Sunshield 3800 Top Coat
- Roofseal Silicone
- Acryflex 1210 Sealant
- Acrylastic 810 White Mastic
- Acrylastic 910 Mastic
- Roof Leveling Compound
- Capseal 800 Roofing Mastic Sealer
- Roofseal Fabrics, Tapes, and Caps
Applications & Uses
- Applications
- Application Area
- Applications & Uses
Preparation
Remove all contaminants and loose material, such as dust, dirt, oil, silicone, release agents, wax, mildew, salt deposits, heavy oxidation, and chalky or loose coating. Check the entire roof surface and thoroughly power wash it. Do not apply at temperatures below 45°F nor during-nor 24 hours preceding- inclement weather, including rain, fog, mist, or freezing tempera- tures. PROTECT FROM FREEZING DURING SHIPMENT AND STORAGE. Do not store material at temperatures below 50°F. Flush all equipment with water before use. Stir Ultraroof thoroughly until uniformly blended, but avoid exces sive mixing to prevent air entrapment.
Application
- Apply a wet coat in even, parallel passes, overlapping each pass 50% to avoid holidays, bare areas, and pinholes. Cross-roll or spray at a right angle to the first pass. On rough surfaces, back roll the first coat to ensure that coating is pushed deep into surface. Alternately, thin Ultraroof with 1 quart water per gallon to achieve better saturation. Over felt surfaces, thin the base coat to achieve maximum penetration. Apply 1 coat of Ultraroof at 1 gallon per 100 sq ft, DFT 8.5 mils.
- Clean equipment with water or water and detergent immediately after use. Allow 4-8 hours to dry. Use Rule-of-thumb test prior to installing the next coat: when one's thumb is pressed firmly to the coating, none of the coating will adhere to the thumb. Apply second, third, and fourth coats, per system specification. For additional durability, roofing granules may be broadcast into the final coating application at the rate of 35-40 ounces per 100 square feet.
Equipment
The following is a guide; suitable equipments from other manufacturers may be used. Changes in pressure, tip size, and equipment may be needed for proper spray characteristics.
- Airless: Standard equipment such as Graco Bulldog Hydra Spray 30 or 45:1 pump with a 0.025-0.031 inch reversible fluid tip.
- Conventional: Industrial equipment such as Binks II:1 Saturn pump or equivalent with air control cut-off, a material hose 3/4 inch ID minimum and an air hose 1/2 inch ID and 50-75 psi air pressure minimum. Heavy mastic spray gun such as Binks 7E2 with 1/4 inch fluid tip or larger and slotted nozzle.
- Brush or Roller: Suitable for waterborne coating. Multiple coats may be required to achieve specified DFT. Roller nap will vary according to texture of substrate and thick- ness of coat; typically a 3/4 inch nap will work.
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Adhesion (Concrete) | 400.0 | psi | ASTM D413 |
| Alkali Resistance | No Effect | — | Fed. Spec. TFC-555B, GSA ex.1 |
| Application Temperature Air and Surface | 45 - 100 | °F | — |
| Application Temperature Air and Surface | 45 - 100 °F | — | — |
| Availability | Shipped Nationaly& Internationally | — | — |
| Availability | Shipped Nationaly& Internationally | — | — |
| Clean Up (75°C) | Water | — | — |
| Curing Mechanism (75°C) | Air Dry | — | — |
| Dry Film Thickness (DFT, 100 ft²/gal) | 8.5 | mils | — |
| Drying Time To Re-Coat (75°C, Dry Through) | 4 - 8 | hours | — |
| Flash Point | min. 215 | °F | SETA |
| Heat Stability | No Viscosity Change | — | Fed. Std. 141 [6051], 160°F for 10 days |
| Moisture Vapor Transmission | 0.6 | pems | ASTM E96, Proc. B, 20 mils DFT |
| Recommended System DFT | 16 - 48 mils total | mils | — |
| Resistance to Ponded Water (75°C) | No Blisters, No Film Degredation | — | — |
| Resistance to Wind-Driven Rain (min.100 mph) | No Weight Gain | — | Fed. Spec. TEC-5558, 4.4.7 min. 95 mph req. |
| Salt-Spray Resistance | No Rusting | — | ASTM D1654 |
| Service Temperature | 32 - 200 | °F | — |
| Solids by Volume | 50 - 54 | % | ASTM D2597 |
| Solids by Weight | 49 - 53 | % | ASTM D2369 |
| Tensile Elongation (At Break) | 1000.0 | % | ASTM D2370, 1 in./min. |
| Tensile Strength (75°C) | 800 | psi | ASTM D2370, 1 in./min. |
| Viscosity (Stormer K.U.) | 95 - 110 | KU | ASTM D562 |
| Volatile Organic Compounds | max. 50 | g/L | US EPA Reference Method 24 |
Technical Details & Test Data
- Performance Data
Safety & Health
- Precautions
Caution
If surface and roof temperatures are between 50-70°F, Ultraroof may be applied in 1 thick coat of 24 wet mils at a rate of 1.5 gallons per 100 square feet. Do not attempt to apply Ultraroof in thick coats when temperatures are above 70°F, since this could cause coating to skin over quickly on top while the coating underneath remains wet, resulting in blisters. Ultraroof is black and its unique resins allow it to dry faster than gray or white coatings, espe- cially in warm, windy weather. When applying polyester sheeting, be careful to apply coating in small areas at a time to ensure that the coating is still wet enough to embed the sheets.
Packaging & Availability
- Packaging
1,5, 55, 275 gallons.
Storage & Handling
- Shelf Life
- 3 years if properly stored