Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Technologies
- Product Families
- Application substrates
Ferrous and non-ferrous metals, galvanized steel and aluminum.
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Application Area
- Fonction - Quality
Protection of cold rolled steels to be welded. Applicable after sandblasting, shot blasting or degreasing. Temporary primary 18 months. Thermal resistance continuously from 150 to 350 °C and discontinuously at 650 ° C. Insensitive to water and steam. Adhesion primer on ferrous and non-ferrous metals.
- Surface Preparation
The support must be suitably prepared: degreased and mechanical or chemical prepared. Do not use on greased, contaminated, rusty, damp, condensing or frozen substrates.
- Paint Préparation
Mix before use then add the suitable thinner under stirring ( linked to the support type to be protected). Make sure that the different constituents (base, thinner) are homogeneous. After thinning, we recommed you to pass the productt hrough a 190 μm filter.
- Application temperature
The temperature of the application cabin, the support and the paint must be between 15 and 30 ° C to obtain an application quality. The substrate temperature must be 3 ° C higher than the dew point temperature. The relative humidity must be less than 65%.
- Application method
Recommended tips Recommended air pressure
Conventional and medium
pressure guns4 to 9 3 to 4 bars Air Mix 1,4 to 1,7 30-60 bars Brush and roller : not recommended - Not adapted to an electrostatic application
cleaning thinner : 501 0009 00- Drying performance
Air at 20°C Time Dust free: 1 hour Touch dry: 15 min Hard dry : 5 min - Steaming
Desolvation 15 minutes at 20°C. Then 30 minutes at 60°C or 15 minutes at 80°C
- Overcoating interval
Minimum 60 minutes when dried at air 20°C/ maximum 6 months without grinding. Do not cover with paints containing chlorinated solvents.
- Pot Life of mixed product
BASE 353 THINNER 502000700
one day when thinned
Properties
- Color
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Recommanded dry film thickness (On steel ) | 20 - 25 | μm | - |
| Recommanded dry film thickness ( On aluminium) | 10.0 | μm | - |
| Maximum film thickness | 25.0 | μm | - |
| wet film thickness | 155.0 | μm | - |
| Coverage ( 100% transfer rate ) | 6.5 - 8 | m²/L | - |
| Dilution for steel substrate (THINNER 502000700) | 15 - 25 | % | - |
| Dilution for aluminium substrate (THINNER 502000700) | 30.0 | % | - |
| Specific gravity (BASE 353) | 0.880 - 1.040 | g/cm3 | - |
| Specific gravity (THINNER 502000700) | 0.795 - 0.815 | g/cm3 | - |
| Mass solid contained (BASE 353) | 25 - 27 | % | - |
| Mass solid contained (THINNER 502000700) | Normally Closed | - | - |
Technical Details & Test Data
- Viscosity at 20°C
Viscosity range of base + Thinner : 15 to 25 secondes in CA4
Packaging & Availability
- Packaging
BASE 353 THINNER 502000700
4 L and 20 L 5 L and 20 L
Storage & Handling
- Shelf Life
BASE 353 THINNER 502000700
24 months 36 months
- Storage temperature
BASE 353 THINNER 502000700
- 5°C à to 35°C protected area