Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- FRAC Code
- Agrochemical Functions
- Technologies
- Composition
ACTIVE INGREDIENT
Sulfur - 80.0%
OTHER INGREDIENT -20.0%
Features & Benefits
- Product Information
Sulfur may damage some crops under certain climatic conditions, such as when temperature is high. Crops grown in greenhouses may be much more sensitive to sulfur injury, so use the lowest labeled rate when using the product on a certain crop for the first time. If no crop injury is observed following treatment, then the application rate may be increased if needed.
Spreaders / stickers are not required for use with this product. If spreaders / stickers are used with this product, foliar injury may be enhanced under high temperatures.
When growing crops for processing, consult the processor before applying this product.
Use Restrictions: Do not use on any crop unless sulfur has been shown to be safe in your locality. Do not allow spray to drift into sulfur-sensitive crops such as Apricots, Cranberries, D’Anjou pears and Spinach and during the growing season. Do not apply this product if temperature will exceed 90°F within the three days following spraying due to the risk of crop injury. Do not use within two weeks of an oil spray treatment except for dormant, delayed-dormant or post-harvest applications with suitable oil. For Citrus, do not apply within 21 days of an oil spray.
Note: The application rates specified for each crop are the maximum that can be applied. These amounts may be reduced if experience or local practice indicates that lesser amounts may be effective. Consult State Agriculture Experiment Station or State Extension Service Specialist for lower rates recommended in your local area.
IMPORTANT: In order to obtain effective Mite and disease control, both the upper and lower sides of plant foliage and fruit must be thoroughly covered by spray solution of this product. Poor spray coverage will result in poor Mite and disease control.
NUTRIENT USE
Product applications will provide sulfur needed to meet the plant’s nutrient requirements and should be considered for use in total nutrient applications. This product can be used as a micronutrient supplement when applied on the foliage or soil to the crops listed on this label. Consult your State Agricultural Experiment Station or Extension Specialist for advice in selecting treatments that best fit local conditions.
Applications & Uses
- Markets
- Applications
- Applicable Crop
- Application Technique
- User Safety Recomendation
USER SAFETY RECOMMENDATIONS
Users should: 1) Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet.
2) Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing.
3) Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.
- Direction For Use
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your state or tribe, consult the agency responsible for pesticide regulation.
- Agricultural Use Requirements
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR Part 170. This standard con-tains requirements for the protection of agricultural workers on farms, forests, nurseries, greenhouses and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about Personal Protective Equipment (PPE) and Restricted Entry Interval (REI). The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the restricted entry interval of 48 hours. For greenhouse uses, do not enter or allow worker entry into treated areas during the REI of 24 hours.
For at least seven days following the application of Copper-contain-ing products in greenhouses:
• at least one container or station designed specifically for flushing eyes is available in operating condition with the WPS-required decontamination supplies for workers entering the area treated with Copper-containing products,
• workers are informed orally, in a manner they can understand:
– that residues in the treated area may be highly irritating to their eyes,
– that they should take precautions, such as refraining from rub-bing their eyes, to keep the residues out of their eyes,
– that if they do get residues in their eyes, they should immedi-ately flush their eyes with the eye flush container that is located with the decontamination supplies and
– how to operate the eye flush container or eye flush station.
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with any-thing that has been treated, such as plants, soil or water is: Coveralls, chemical-resistant gloves made of any waterproof material, shoes plus socks and protective eyewear.
- Non-Agricultural Use Requirements
The requirements in this box apply to uses of this product that are NOT within the scope of the Worker Protection Standard for agricultural pesticides (40 CFR Part 170). The WPS applies when this product is used to produce agricultural plants on farms, forests, nurseries or greenhouses.
Do not enter or allow others to enter the treated area until sprays have dried.
Avoid working in spray mist.
Keep all unprotected persons out of operating areas or vicinity where there may be danger of drift.
Certain states may require more restrictive re-entry intervals; consult your State Department of Agriculture for further information.
Properties
- Formulation Type
Safety & Health
- Precautionary Statements
Hazards to Humans and Domestic Animals
CAUTION: Harmful if swallowed, inhaled or absorbed through skin.
Causes moderate eye irritation. Avoid contact with skin, eyes or clothing. Avoid breathing spray mist.
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Some materials that are chemical-resistant to this product are listed below.
Applicators and other handlers must wear: Long-sleeved shirt and long pants, chemical-resistant gloves made of any waterproof material (such as Natural Rubber), shoes, socks and protective eyewear.
Follow manufacturer’s instructions for cleaning / maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
ENGINEERING CONTROLS
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for Agricultural Pesticides [40 CFR 170.240(d)(4-6)], the handler PPE requirements may be reduced or modified as specified in the WPS.
- Environmental Hazards
Do not apply directly to water or to areas where surface water is present or to intertidal areas below the mean high water mark. Do not contaminate water when disposing of equipment washwater or rinsate.
- Physical And Chemical Hazards
Sulfur dust suspended in air ignites easily. Keep away from heat, sparks or flame. Do not smoke while applying this product.
Packaging & Availability
- Packaging Type
Storage & Handling
- Storage And Disposal
Do not contaminate water, food or feed by storage or disposal.
PESTICIDE STORAGE: Store in original container. This product will freeze at a temperature of approximately 5ºF, but upon warming, will thaw out to a fully homogeneous product.
PESTICIDE DISPOSAL: Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal facility.
CONTAINER HANDLING:
Nonrefillable Container (rigid material; less than 5 gallons):Nonrefillable container. Do not reuse or refill this container. Offer for recycling, if available. Clean container promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container one-fourth full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Dispose of empty container in a sanitary landfill or by incineration, or, if allowed by State and local authorities, by burning. If burned, stay out of smoke.
Nonrefillable Container (rigid material; 5 gallons up to < 250 gallons): Nonrefillable container. Do not reuse or refill this container. Offer for recycling, if available. Clean container promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container one-fourth full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. Dispose of empty container in a sanitary landfill or by incineration, or if allowed by State and local authorities, by burning. If burned, stay out of smoke.
Refillable Container (≥ 250 gallons & Bulk): Refillable container. Refill this container with pesticide only. Do not reuse this container for any other purpose. Cleaning the container before final disposal is the responsibility of the person disposing of the container. Cleaning before refilling is the responsibility of the refiller. To clean the container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the container about 10% full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this rinsing procedure two more times. Then offer for recycling if available or reconditioning if appropriate or puncture and dispose of in a sanitary landfill, or by other procedures approved by State and local authorities.