Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Name
- Polymer Name
- CAS No.
- 1309-64-4
- EC No.
- 215-175-0
- Technologies
- Product Families
- Type
HFFR Low Voltage Polyolefin Insulation
Features & Benefits
- Labeling Claims
Applications & Uses
- Applications
- Cure Method
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Applications
AquaGraft® 61-7125 is designed for use in SAE J1127 and 125°C automotive cable applications. These two components, when blended in a 80% AquaGraft® 7125/20% CMB-6001 blend ratio, will meet numerous requirements for low voltage insulation and be suitable for flame retardant 125°C applications.
- Applications
Appliance, Automotive, Battery, Welding
Properties
- Mechanical Properties
- Thermal Properties
| Value | Units | Test Method / Conditions | |
| Elongation | 210 | % | — |
| Specific Gravity | 1.35 | g/cm³ | — |
| Tensile Strength | 1730 | psi | — |
| Value | Units | Test Method / Conditions | |
| Automatic Transmission (at 50°C) | 4 | % | — |
| Battery Acid (at 23°C) | 0 | % | — |
| Diesel (at 23°C) | 6 | % | — |
| Engine Coolant (at 50°C) | 0 | % | — |
| Engine Oil (50°C) | 3 | % | — |
| Ethanol (at 23°C) | 2 | % | — |
| Gasoline (at 23°C) | 12 | % | — |
| Power Steering Fluid (at 50°C) | 6 | % | — |
| Retained Elongation (7 Days in 121°C Air Oven) | 95 | % | — |
| Retained Elongation (7 Days in 158°C Air Oven) | 97 | % | — |
| Retained Tensile (7 Days in 121°C Air Oven) | 106 | % | — |
| Retained Tensile (7 Days in 158°C Air Oven) | 114 | % | — |
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
- Quality Standards
- Specifications
When extruded and cured consistent with standard safe and acceptable wire and cable industry practices, cable insulated with AquaGraft® 61-7125 is designed to comply with the requirements as specified in the following standards. It is important to note that overall cable construction plays an important role in flame, fluid, and electrical performance.
SAE J1127
SAE J1128
ISO 6722- Certification
- Certified Test Results including physical test data are included with each shipment.
Technical Details & Test Data
- Processing
AquaGraft® 61-7125 is engineered for processing on conventional extrusion equipment. It is recommended that these products be processed using a greater than 20:1 extruder with a high shear screw with adequate mixing sections. The compound supplied is in the cleanest state and is of the highest quality; however, the use of a breaker plate with a screen pack of approximately 20/20 or 20/40 mesh is recommended for optimal rheological flow and steady back pressure.
A high level of care in storage of CMB-6001 to minimize exposure to moisture is recommended to ensure that there is no degradation.
Pre-heating of the conductor may be recommended depending on cable construction and specific processing conditions.
Pre-drying of AquaGraft® 7125 is generally recommended prior to use for 4 hrs. at 150°F.The following conditions are given as a guide for processing:
Temperature Profile
°F
ºC
Zone 1 (feed):
310
154
Zone 2:
320
160
Zone 3:
320
160
Zone 4:
330
165
Crosshead:
330
165
Die:
330
165
Packaging & Availability
- Packaging
- 2200 pounds (997.9 Kg) per box
- 200 pounds (90.7 Kg) per fiber drum
- PE Liners
- Use within 12 months of manufacturing date
Storage & Handling
- Storage
A high level of care in storage to minimize exposure to moisture is recommended to ensure that there is no degradation of the CMB 6001. Once opened, CMB-6001 should be consumed immediately to avoid any premature gelling due to environmental moisture.
- Handling
- To ensure health and safety, Material Safety Data Sheets (MSDS) are available and should be consulted prior to use.