Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Polymer Name
- Technologies
- Product Families
- Type
Low Voltage Polyolefin Base
Features & Benefits
- Labeling Claims
- Materials Features
Applications & Uses
- Applications
- Cure Method
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Applications
- AquaGraft® PEMC-1 is designed for use in low voltage (2kv) wire and cable applications. AquaGraft® PEMC-1, when used in correct ratios with available Flame Retardant masterbatch will allow the cable to pass various industry recognized flame tests and perform in wet electrical applications as well as high temperature appliance constructions.
- Applications
Appliance, Automotive, Control, UL 44
Properties
- Mechanical Properties
- Thermal Properties
Value | Units | Test Method / Conditions | |
Specific Gravity | 0.92 | g/cm³ | — |
Tensile Strength | 2400 | psi | — |
Elongation | 360 | % | — |
Hot Creep Elongation | 60 | % | — |
Value | Units | Test Method / Conditions | |
Retained Elongation (7 Days in 121°C Air Oven) | 100 | % | — |
Retained Elongation (7 Days in 136°C Air Oven) | 100 | % | — |
Retained Elongation (7 Days in 158°C Air Oven) | 90 | % | — |
Retained Tensile (7 Days in 121°C Air Oven) | 105 | % | — |
Retained Tensile (7 Days in 136°C Air Oven) | 105 | % | — |
Retained Tensile (7 Days in 158°C Air Oven) | 110 | % | — |
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
- Quality Standards
- Specifications
When extruded and cured consistent with standard safe wire and cable industry practices, cable insulated with the correct ratios AquaGraft® PEMC-1 and FMB Masterbatch/CMB-432 will comply with the requirements as specified in the following standards:
UL 44 for:
XHHW, XHHW-2
SIS, USE, USE-2
UL/CSA AWM applications up to 150C
Horizontal Flame *
VW-1 on larger cable sizes *
*(When used with appropriate level of FR master-batch)
Technical Details & Test Data
- Processing
AquaGraft® PEMC-1 is engineered for processing on conventional extrusion equipment. It is recommended that this product be processed using a greater than 20:1 extruder with a high shear screw with adequate mixing sections. The compound supplied is in the cleanest state and is of the highest quality; however, the use of a breaker plate with a screen pack of approximately 20/40 or 20/60 mesh is recommended for optimal rheological flow and steady back pressure.
A high level of care in storage to minimize exposure to moisture is recommended to ensure that there is no
pre-cure or gelling of the grafted polymer.
Pre-heating of the conductor is recommended depending on cable construction and specific processing
conditions.
The following conditions are given as a guide for processing:Zone 1 (feed): 260-280 127-138 Zone 2 260-280 127-138 Zone 3 260-280 127-138 Zone 4 260-280 127-138 Crosshead 280-300 138-149 Die 280-300 138-149 Values ae shown in °F and °C respectively.
:
Packaging & Availability
- Packaging
- 1500 pounds (680.4 Kg) per box
- 200 pounds (90.7 Kg) per fiber drum
- Foil Liners
Storage & Handling
- Storage
- A high level of care in storage to minimize exposure to moisture is recommended to ensure that there is no degradation of the PEMC-4. Once opened, PEMC-4 should be consumed immediately to avoid any premature gelling due to environmental moisture.
- To ensure health and safety, Material Safety Data Sheets (MSDS) are available and should be consulted prior to use.