Products

2-hydroxy-2-methyl-1-phenyl-1-propanone is a fast curing type-I photoinitiator. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-4265 is a 50:50 liquid blend of 2-hydroxy-2-methyl-1-phenyl-1-propanone and diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide. It provides exceptional cure response in white and pastel pigmented systems as well as thicker clear films. It provides a perfect balance between surface cure and through cure to enable the best possible adhesion in these systems. PL-4265 soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-7021 has a unique structure which results in a flexible cured product. Adding PL-7021 to formulations has been shown to increase toughness.

4-phenyl benzophenone is a very fast curing type-II photoinitiator. In the presence of O2, the use of an amine co-initiator is recommended. It is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-3208 Ethoxylated Bisphenol A Dimathacrylate is a difunctional monomer providing low volatility and flexibility.

2-Methyl-1-[4-(methylthio) phenyl]-2-morpholino propan-1-one is a type I photoinitiator primarily used in pigmented systems. It is oftentimes used with PL-ITX as a sensitizer to enhance the curing efficiency in inks. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-7110 is a low color urethane that is a viscous liquid at room temperature. Upon cure, PL-7110 creates a tough polymer with percent elongation near 60%. PL-7110 is non-yellowing and can be used in formulations to add toughness.

PL-7210 has a unique combination of high tensile strength and good elongation, which results in excellent toughness upon curing. PL-7210 is also very low color.

Diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide is a Type I photoinitiator best known for it's through cure abilities. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-7113 is a non-yellowing urethane that exhibits a high degree of elongation. It also has a high rate of conversion with low average shrinkage stress. PL-7113 can be added to formulations to add toughness.

PL-600 is a liquid Photoinitiator compound developed specifically for white and pastel pigmented systems as well as thicker clear films. It provides a perfect balance between surface cure and through cure to enable the best possible adhesion in these systems. Because it's a liquid, it works well as a press side additive for the printer. PL-600 is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-500 is a eutectic blend made up of a 1:1 mixture of PL-CPK and PL-BPO. It is well suited for applications where ease of use and good surface cure are needed. PL-500 is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-CLR is a liquid photoinitiator compound developed specifically for thicker clear films where low yellowing is necessary. It provides a perfect balance between surface cure and through cure to enable the best possible adhesion in these systems. Because it’s a liquid, it works well as a press side additive for the printer. PL-CLR is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

Benzil dimethyl ketal is a fast curing type-I photoinitiator. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-3201 Polyethylene Glycol 200 Dimethacrylate is dimethacrylate difunctional monomer. It's used in 3D printing,Adhesives and Sealants applications. It provides excellent adhesion, flexibility and impact strength.

PL-3209 is a difunctional monomer providing a good balance of hydrophobicity and hydrophilicity.

PL-DRK is a liquid photoinitiator compound developed specifically for dark and black inks and coatings. It provides an optimum balance between surface cure and through cure to enable the best possible adhesion in these systems. Because of it's optimum viscosity, it can be used in flexo, screen and paste inks without negatively effecting rheology. It is also well suited as a press side additive for the printer. PL-DRK is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-7013 has a relatively low viscosity but upon curing exhibits high conversion and low shrinkage. It exhibits excellent flexibility once cured. PL-7013 is very low color.

PL-TINP is a highly efficient hydroxyphenol benzotriazole ultraviolet light absorber (UVA).

4-Methyl benzophenone is a fast curing type-II photoinitiator. In the presence of O2, the use of an amine co-initiator is recommended. It is soluble in most monomers, oligomers and pre-polymers. It is insoluble in H2O.

PL-3204 is a difunctional monomer providing flexibility and hydrophobicity.

PL-7011 exhibits excellent flexibility upon curing. It is a non-yellowing extended urethane dimethacrylate and can be used in formulations to add toughness.

PL-3214B is a difunctional reactive monomer that provides excellent diluecy as well as water resist. and weathering prop.

PL-3102 is a monofuctional monomer that provides water resistance and flexibility.

PL-IND is a liquid photoinitiator compound developed specifically for dark and black inks and coatings where acid adhesion promoters are present.. It provides an optimum balance between surface cure and through cure to enable the best possible adhesion in these systems. Because of it’s optimum viscosity, it can be used in most coating and ink systems without negatively effecting rheology. It is also well suited as a press side additive for the printer PL-IND is soluble in most monomers, more

PL-LTE is a liquid photoinitiator compound developed specifically for lighter colored (non white) inks and coatings. It provides an optimum balance between surface cure and through cure to enable the best possible adhesion in these systems. Because of it’s optimum viscosity, it can be used in flexo, screen and paste inks without negatively effecting rheology. It is also well suited as a press side additive for the printer PL-LTE is soluble in most monomers, oligomers and pre-polymers. It is more

2-Isopropylthioxanthone is a Type II photoinitiator. It is typically used in combination with tertiary amines. Another major use is as a sensitizer to enhance the curing efficiency of both PL-907 and PL-369. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-100 is a 70:30 blend of oligo [ 2-hydroxy-2-methyl-1-[ 4-(1-methylvinyl) phenyl] propanone] and 2-Hydroxy-2-methyl-1-phenyl-1-propanone. It is a fast curing type-I photoinitiator soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-3218 is a difunctional monomer providing low viscosity and high boiling point.

PL-3103 is a monofunctional monomer that provides good adhesion and low shrinkage.

PL-7100B has a very high conversion rate upon curing, resulting in low shrinkage and a high strength material. PL-7100B is non-yellowing and can be used in formulations to add strength.

PL-3216A is a difunctional monomer providing water resistance and fast cure.

PL-3116 is a monofunctional monomer providing good adhesion, high Tg, and low viscosity.

2-Benzyl-2-dimethylamino-1-(4-morpholinphenyl) butanone is a type I photoinitiator primarily used in non-white pigmented systems. It is oftentimes used with PL-ITX as a sensitizer to enhance the curing efficiency in inks. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

2-Ethylhexyl 4-dimethylamino benzoate is a tertiary amine synergist typically used in combination with type II photoinitiators such as Benzophenone. It is best known for its ability to promote surface cure. It is soluble in most monomers, oligomers and pre-polymers but insoluble in H2O.

PL-7000 is a low viscosity urethane dimethacrylate. When cured, PL-7000 exhibits good hardness and strength. PL-7000 is low in color.