Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- Composition
Excel-Coat Glaze is a single-component, acrylic polymer clear top coat.
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Limitations
- Not for areas intended for vehicular traffic.
- Do not apply in constantly submerged conditions such as reflecting ponds or tank linings.
- Do not apply over non-structural lightweight concrete without prior written approval.
- Not recommended as a top coat around pool areas. Refer to the Excel-Coat Acrylic Lacquer Sealer for applications around pool and spa areas.
- Grade
The Excel-Coat Glaze is a clear acrylic resin to be used as a top coat. This top coat can be used with all Excel-Coat systems.
- Job Conditions
Before any work is started, the applicator shall thoroughly examine all surfaces for any deficiencies. Should any deficiencies exist, the Architect, Owner or General Contractor shall be notified in writing and any corrections necessary shall be made.
Cold or inclement weather will affect the cure time of all Excel- Coat products. Do not install over wet substrate, in the rain or, if the threat of rain exists within 24 hours.- Installation
Preparation:
1. Curing of concrete shall be by means of water cure or dissipating compounds. Curing compounds shall be approved by an authorized representative of Excellent Coatings International.
2. Concrete shall be cured a minimum of 28 days prior to installation of the Excel-Coat Glaze unless approved by an authorized representative of Excellent Coatings International.
3. Concrete finish shall be a power metal float followed by a light steel trowel and fine hair broom finish, or equivalent.
4. Concrete surfaces shall be free of excessive roughness, voids, protrusions or exposed aggregate.
5. All tooled joints and control joints shall be caulked with a sealant approved by Excellent Coatings International. Moving structural cracks shall be treated with an epoxy crack repair material.
6. To top coat existing systems, the system must be thoroughly cleaned (power washing with a detergent like TSP or Excel-Coat All Purpose Cleaner is acceptable) and primed.
7. All decks shall be properly sloped to freely drain and eliminate the ponding of water. All expansion joints shall be treated as specified in the drawings and in strict accordance with Excellent Coatings International's written instructions. Excellent Coatings International shall be consulted for specific design requirements.- Applications
For Existing Systems:
1. Thoroughly clean surface by power washing prior to application of the top coat. Allow surface to dry completely.
2. Prime surface with Excel-Coat Primer at the rate of approximately 250 square feet per gallon.
3. Allow primer to become tacky. Apply two thin coats of Excel-Coat Glaze by roller or airless sprayer at the rate of 250 square feet per gallon per coat, for a net yield of 125 square feet per gallon total coverage. Allow to dry approximately 8 hours. Allow to cure 24 hours before heavy foot traffic is permitted and an additional 72 hours before heavy objects are placed on the surface.
For New Excel-Coat Systems: (i.e.: K/D systems or two-tone texture systems)
1. A primer coat is not necessary prior to application of the Excel-Coat Glaze.
2. Apply two thin coats of Excel-Coat Glaze by roller or airless sprayer at the rate of 250 square feet per gallon per coat, for a net yield of 125 square feet per gallon total coverage. Allow to dry approximately 8 hours. Allow to cure 24 hours before heavy foot traffic is permitted and an additional 72 hours before heavy objects are placed on the surface.
Properties
- Color
Safety & Health
- Health And Hazard Information
Use the product with adequate ventilation and personal protection.
- Maintenance
Cleaning can be accomplished by scrubbing with normal detergent soap and water. Heavy stains may require TSP solution and brushing with a stiff broom. Excel-Coat Maintenance Cleaner is also an effective cleaning material and may be used in conjunction with power washing. Follow product instructions.
- Guarantee / Warranty
Excellent Coatings International warrants Excel-Coat Glaze to be free of defects and manufactured to meet published physical properties for a period of one year following the date of shipment, provided that the product has been applied according to the manufacturer's instructions. Under this warranty, Excellent Coatings International will provide, at no charge, product in containers to replace any product proved to be defective in applications recommended by us as suitable for this product. All claims concerning the products' defects must be made within twelve months of shipment and within thirty days of discovery. Absence of such claims in writing during this period will constitute a waiver of all claims with respect to such product. This warranty is IN LIEU OF any and all other warranties, expressed or implied, including, but not limited to, any implied warranty of MERCHANTABILITY of fitness for a specific purpose.
Packaging & Availability
- Packaging
The Excel-Coat Glaze is available in 1 and 5 gallon containers U.S. gallon measures).
- Colors
Excel-Coat Glaze is a clear non-yellowing acrylic top coat.
- Availabilty
Immediately available from Excellent Coatings, Inc, and authorized distributors.
- Cost
Cost data is available from your local Excellent Coatings International authorized representative.
Storage & Handling
- Shelf Life
Twelve months from shipping date stored below 80°. Do not allow product to freeze.
- Storage and Handling
Store Excel-Coat Glaze in a cool, dry area and protect from freezing. It will be necessary to stir Excel-Coat Glaze before using. Partial containers can be resealed. Should a top skin develop on the remaining contents of a container, the physical properties and effectiveness of the contents will not be impaired. Clean mixing and application tools with water. Dispose of empty containers properly according to current Local, State and Federal regulations.