Knowde Enhanced TDS
Identification & Functionality
- Carrier
- Technologies
- Product Families
- Composition
Excel-Coat Primer 120 is a two-component, liquid applied, water-borne epoxy primer designed for concrete, existing decorative coatings and textured waterproofing systems.
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Compatible Substrates & Surfaces
- Limitations
- Do not allow product to freeze.
- Do not apply to surfaces which are designated as wet areas.
- Job Conditions
Applicator shall thoroughly examine all surfaces for any deficiencies. Should any deficiencies exist, the Architect, Owner or General Contractor shall be notified in writing and any corrections necessary shall be made. The surface temperature of the substrate should be a minimum of 45°F.
- Installation Over Concrete
Preparation:
1. Curing of concrete shall be by means of water cure or dissipating compounds. Curing compounds shall be approved by an authorized representative of Excellent Coatings International
2. Concrete shall be cured a minimum of 28 days prior to installation of the Excel-Coat Primer 120 unless approved by an authorized representative of Excellent Coatings International.
3. Concrete finish shall be a power metal float followed by a light steel trowel and fine hair broom finish, or equivalent.
4. Concrete surfaces shall be free of excessive roughness, voids, protrusions or exposed aggregate.- Applications
1. Open both base and hardener containers. The base container is not full, in order to pour the contents of the hardener container into the base container.
2. Using a drill motor and a mixing attachment, mix the resin and the catalyst thoroughly.
3. Using care, apply mixed primer by roller or brush creating a thin, even coat. One gallon kit should cover approximately 250-350 square feet.
4. Allow primer to become tacky at least 1-3 hours at 70°F (12°C) before application of the Excel-Crete material. Excel-Crete should be applied while primer is slightly tacky. For epoxy or urethane coatings, allow primer to become tack free. This process takes 2-6 hours.- Installation Over Existing Coatings
Preparation:
1. Existing coatings shall be tightly adhered with no cracking, peeling or chipping. Surface shall be clean and dry. It is recommended that existing coatings that are to be re-coated be approved by an authorized representative of Excellent Coatings International.
Note: If primer cures longer than one day before application of acrylic materials, then re-prime surface.
Properties
- Typical Properties
Value | Units | Test Method / Conditions | |
Primer 120 | 25.76 - 26.24 | % | D-1353 |
Weight Per Gallon (Mixed) | 8.3 | lbs | D-1475 |
Viscosity (77°F, Mixed) | 150.0 | cps | D-2393 |
Volatile Organic Compound (VOC) Content | 150.0 | grams/liter | Calculated |
Flash Point (Mixed) | max. 200 | °F | D-1310-82 |
Mix Ratio | Prepackaged Kits | - | - |
Pot Life ( l Quart, 75ºF) | 2 hours | - | D-2471 |
Cure Time (77°F, 50% R.H.) | 2 to 3 hours | - | - |
Firm to Touch Tack Free | 1 - 2 | hours | - |
Coverage | 250 - 350 | sq ft/gallon | - |
Cured Film Flexibility (Passes) | 2022-01-08 | inch | Mandrel Bend |
Cured Film Impact (Passes) | 60.0 | inch/lbs | Reverse Impact |
Safety & Health
- Health And Hazard Information
Use the product with adequate ventilation and personal protection.
- Maintenance
Cleaning can be accomplished by scrubbing with detergent soap and water. Heavy stains may require TSP solution and brushing with a stiff broom.
- Guarantee / Warranty
Excellent Coatings International warrants Excel-Coat Primer 120 to be free of defects and manufactured to meet published physical properties for a period of one year following the date of shipment, provided that the product has been applied according to the manufacturer's instructions. Under this warranty, Excellent Coatings International will provide, at no charge, product in containers to replace any product proved to be defective in applications recommended by us as suitable for this product. All claims concerning the product's defects must be made within twelve months of shipment and within thirty days of discovery. Absence of such claims in writing during this period will constitute a waiver of all claims with respect to such product. THIS WARRANTY IS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A SPECIFIC PURPOSE.
Packaging & Availability
- Grade
- Excel-Coat Primer 120 or 120-CA Part A – Base Resin
- Excel-Coat Primer 120 or 120-CA Part B - Hardener
- Packaging
Excel-Coat Primer 120 is available in 1 & 2 gallon kits. Excel Coat Primer 120-CA is the California VOC Compliant formula and is available in 1 gallon kits.
- Availabilty
Immediately available from Excellent Coatings International and authorized distributors.
- Cost
Cost data is available from your local Excellent Coatings International authorized representative.
Storage & Handling
- Shelf Life
Twelve months from manufacturing date stored below 80°F and above 35°F. Do not allow product to freeze.
- Storage and Handling
Store Excel-Coat products in a cool, dry area and protect from freezing. Partial containers can be resealed if the two parts have not been mixed. Should a top skin develop on the remaining contents of a container, the physical properties and effectiveness of the contents will not be impaired. Clean mixing and application tools with water. Dispose of empty containers properly according to current Local, State and Federal regulations.