Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Application Method
- Compatible Substrates & Surfaces
- Equipment Preparation
Compatible Materials: All equipment surfaces must be constructed of stainless steel, polyethylene, polypropylene or similar, chemical resistance substances. Mild steel, brass, copper, and polyvinyl chloride (PVC) or plasticizer-containing materials cannot be allowed to contact the coating solution.
Cleaning: All coating equipment must be thoroughly cleaned with a compatible solvent to remove all traces of other coatings, solvents, or old batches of the same product. After all residues have been removed from the equipment, multiple rinses of butanol are used to prepare the system for the introduction of filtered S-30AP Hardcoat solution. Dried Hardcoat residue may be removed with an aqueous 25 - 40% solution of sodium or potassium hydroxide.
- Application Parameters
Property Range Application Method Dip 1.5 – 3.5 mm /second withdrawal rate
Spray 20 - 45 psi HVLP; fine tip
Flow Coat As appropriate to flow system
Suggested Primers SP-1 Primer on extruded polycarbonate
Environment Temperature/Humidity 16-27°C / 20-45% RH
Dew point Dew point must be at least 15˚ lower than room temperature
Air quality Laminar, top-down flow < 5 cfm, Particle count as appropriate ( ≤ Class 10,000 )
Coating Temperature Within 2˚ of Ambient temperature
Coating Filtration Polyethylene or polypropylene; nominal media rated at 0.5 to 1.0 microns as a pre-filter; absolute media rated at 5.0 to 10.0 microns. Filter before every use.
Cure Conditions 1 - 2 Hours at 90˚C, 30 - 45 Minutes at 120°C
Properties
- Color
- Typical Properties
- Properties
-
Resistant to abrasion and chemicals in combination with SP-1 primer
-
Transparent, high-gloss finish
-
Thermal Curing
-
Value | Units | Test Method / Conditions | |
Adhesion (5B) | 100.0 | % | - |
Chemical Resistance (Fail) | Concentrated Alkali, Hydrofluoric Acid, Dichloromethane, | - | - |
Chemical Resistance (Pass) | Alcohols (Ethanol/isopropanol), Aliphatic (diesel/gasoline/heptane/cyclohexane), Esters (ethyl acetate), Ketones (acetone, 2-heptanone;2-butanone), Dilute alkali, Concentrated/Dilute acids (except hydrofluoric). Primer is suggested for maximum chemical resistance. | - | - |
Compatible Solvents (25°C) | Isobutanol or n-butanol | - | - |
Haze | max. 1 | % | - |
Light Transmittance | min. 88 | % | - |
Light Transmittance (Glass) | min. 99 | % | - |
Maximum Dilution (25°C, Coating) | 80.0 | % | - |
Maximum Dilution (25°C, Solvent) | 20.0 | % | - |
pH (25°C) | Slightly acidic | - | - |
Solids (by Weight, 25°C) | 25 - 30 | % | - |
Specific Gravity (25°C) | 0.94 - 0.95 | - | - |
Thickness, microns | 2.0 - 6.0 | Microns | - |
Viscosity (25°C) | 15 - 20 | Centipoise | - |
Safety & Health
- Safety and Exposure
All users must read and understand the Safety Data Sheet prior to using this product.
Packaging & Availability
- Delivery Options
The S-30AP Hardcoat solution is available for shipment within two weeks of order confirmation, and is available in quart, gallon, five-gallon pail, and 55- gallon drum containers. Contact Exxene to select the best payment option and the optimum shipping method according to your preference and region. All charges, duties, and fees associated with the shipment and its contents are the responsibility of the customer.
Storage & Handling
- Storage
S-30AP Hardcoat solution is stored at room temperature, or at refrigerated temperatures. When stored in the original, sealed container, the solution should be used within six months.