Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- For interior or exterior use.
- Excellent adhesion to porcelain tile and to diffi cult to bond substrates.
- Excellent flexibility and bond strength.
- Excellent workability.
- Easy to use - just mix with water and apply.
- Water resistant when cured.
- Rated as a light performance commercial and residential mortar by ASTM C627-70 on plywood substrates.
- Rated as suitable for extra heavy service by ASTM C627-70 on concrete substrates.
Applications & Uses
- Markets
- Applications
- Application Area
- Application Method
- Cure Method
- Basic Uses
- Installation of porcelain, ceramic, mosaic, quarry and paver tile.
- Installation of many types of natural stone, marble, granite, slate and precast terrazzo tile.
- Recommended Surfaces
- Interior or exterior floor and wall installations*.
- Vertical or horizontal surfaces of concrete, masonry, terrazzo, cement backerboards.
- Installation over cement mortars and leveling compounds.
- Existing surfaces of properly prepared tile, stone or cementitious terrazzo.
- Exterior grade plywood or gypsum board, in interior dry areas only.
- Existing surfaces of properly prepared non-cushion sheet vinyl fl ooring, VCT or cutback adhesive residue.
- Flextile waterproofi ng, crack-isolation and sound reduction membranes.
- Limitations
- Do not use over particleboard, Masonite, chipboard, OSB or similar unstable materials.
- Do not use over cushioned resilient fl ooring, rubber, plastic, paint, asphalt, or plywood surfaces in wet areas.
- Do not use over single layer plywood fl oors. Use only on surfaces, which are maintained at a temperature above 10°C (50°F) and below 35°C (95°F) during application and for at least 72 hours after application.
- To use directly over gypsum-based patching or leveling substrates, apply suitable primer before use.
- On exterior applications, protect from rain until thoroughly dried and protect from freezing for at least 14 days after installation.
- When installing light-colored stones and translucent marble use Flextile 52 White.
- Installations over nonporous surfaces may require extended setting/curing times.
- Do not use for moisture-sensitive stone such as green marble, certain limestone and granite, agglomerate tiles, cultured marble or resin-backed Instead, use Flexepoxy 100 mortar.
- For installations subject to severe freeze/thaw conditions use Flextile two component systems.
- Installation
Preparatory Work: Surfaces must be sound, even, dry and free of grease, oil, dirt, paint, curing compounds or sealers, or other foreign matter. Surfaces must be true to a tolerance of 3 mm (1/8”) in 2.4 meters (8 ft.) for walls and 6 mm (1/4”) in 3 meters (10 ft.) for fl oors. Concrete surfaces should have a wood fl oat or steel trowel with broom fi nish. Roughen smooth concrete surfaces. Plywood fl oors should be designed for maximum defl ection of L/360 of span. This normally requires an overlay of 16 mm (5/8”) exterior grade plywood over 25 mm (1”) nominal boards or 16 mm (5/8”) plywood when on joists 40 cm (16”) O.C. Fasten overlay with screw type nails and glue where possible. Leave a 3 mm-6 mm (1/8”-1/4”) gap between sheets of overlay and next to all vertical surfaces to allow for expansion. Refer to current editions of TTMAC 09 30 00 Tile Installation Manual, or TCNA Handbook For Ceramic Tile Installation for information regarding placement of expansion or control joints, or for further substrate acceptability information.
Application: Mix with approximately 5 liters (1.3 US gallons) of water per 22.7 kg (50 lb) bag. Avoid using high-speed mixers. Allow mixed mortar to slake for at least 10 minutes, then re-mix without adding further water. Spread a thin layer of mixed mortar with fl at side of trowel to wet out the substrate; then reapply suffi cient material with a suitable notched trowel that will leave enough mortar to give at least 95% coverage to the backs of tile. Back buttering of tile is recommended for porcelain tile, large format or high lugged tile, ungauged slate, stone, etc. and for all exterior applications. Comb that area which can be covered with tile before skinning occurs. Mortar should be troweled with notches running in straight lines so as to achieve maximum coverage. Press or beat in tile to achieve a fi nished thickness of mortar of at least 3mm (1/8"). Do not adjust tiles after they have been set for more than 25 minutes
- Curing and Grouting
Protect from all traffic and delay grouting until cured at least 24 hours, and preferably 48 hours. On exterior or cold weather applications, extended curing is recommended to ensure that mortar is sufficiently cured prior to grouting. Grout using Flextile Polymer Modified Grout or Flextile FlexEpoxy 100 100% Solids Epoxy Grout, or Flextile ColourMax Plus Pre-Mixed Urethane Grout
- Maintenance
No maintenance is required except where damages result from unforeseen circumstances.
- Technical Service
Flextile maintains a well-equipped laboratory able to test its products in conjunction with the products with which they are used.
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Approx. Coverage (Per 22.7 Kg Bag, 10 mm (3/8") notched trowel) | 5.5 | m² | — |
| Approx. Coverage (Per 22.7 Kg Bag, 5 mm (3/16") notched trowel) | 10.0 | m² | — |
| Approx. Coverage (Per 22.7 Kg Bag, 6 mm (1/4") notched trowel) | 7.1 | m² | — |
| Cleanability | With water before material dries | — | — |
| Final Cure | 28.0 | Days | — |
| Initial Cure | 24-48 | Hours | — |
| Open Time | 20.0 | Minutes | — |
| Pot Life | 2.0 | Hours | — |
| VOCs | 0.0 | g/l | — |
Technical Details & Test Data
- Technical Data
Exceeds ANSI A118.4 and A118.11 specification requirements.
Description ANSI Spec. Typical Result 28 Day Shear Strength MPa MPa Glazed Wall Tile min. 2.07 3.11 to 4.14 Impervious Ceramic Tile (Porcelain) Mosaics min. 1.38 2.59 to 3.45 Quarry Tile min. 1.03 2.42 to 3.45 Quarry Tile / Plywood min. 1.03 1.38 to 1.79
Safety & Health
- Caution
Freshly mixed cement, mortar, concrete or grout may cause skin injury. Avoid extended contact with skin where possible and wash exposed skin areas promptly with water. If any cement or cement mixtures get into the eye, rinse immediately and repeatedly with water and get prompt medical attention. Keep out of reach of children.
Packaging & Availability
- Packaging Type
- Availability
Versatile 52 Premium-Grade, Polymer-Modifi ed Mortar is availablefrom Flextile Ltd. and its distributors in 22.7 kg (50 lb), and 11.3 kg (25 lb).
Storage & Handling
- Shelf Life
- 1 Year