Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features
- Dries to a clear appearance.
- Ready-Mixed
- Low VOC
- Water-Based
- Vapor permeable
- Abrasion/Mar resistant
- Dirt Pickup Resistant
- Benefits
- Ready to use on site; no additional additives needed.
- Environmentally safe.
- 100% acrylic, safe, non-toxic; cleans up with water.
- Allows substrate to breathe naturally.
- Increased abrasion resistance.
- Stays cleaner longer.
Applications & Uses
- Application Method
- Surface Preparation
All surfaces must be fully cured, structurally sound and free of weak or damaged surface conditions such as laitance or spalls. Surfaces must be clean, dry, frost-free, and free of any bond-inhibiting materials such as dust, dirt, oil, form release, algae, mildew, salts, efflorescence, or any other surface contamination.
- Mixing
Mix with a clean, rust-free electric drill and paddle to a uniform consistency. Close container when not in use. Clean tools with water immediately after use.
- Application
Apply only in well-ventilated areas to structurally sound, clean, dry, properly prepared and primed, frost-free surfaces.
Important - Always construct a mock-up under actual conditions of use to verify proper surface preparation, number of coats required, and approval of finished look by the appropriate authority.
DecoSeal is applied by roller with 2 thin coats, allow DecoSeal to dry between coats approximately 2-3 hours at 70°F and 50% RH. Protect from freezing for a minimum of 24 hours after application. Drying time will vary based on ambient air conditions, increased humidity and lower air temperatures will increase cure time. Avoid application in cool damp conditions.
Curing/Drying - The drying time of DecoSeal is dependent upon the air temperature and relative humidity. Under average drying conditions (70°F (21°C), at 55% R.H.), DecoSeal is dry to the touch in 2 hours. Protect work from rain for at least 24 hours.
Clean Up - Clean tools and equipment with water immediately after use. Remove dried material from tools and equipment mechanically.
- Coverage
Coverage depends on the texture and porosity of the surface/substrate. For sealing new applications, the coverage is approximately 1200-1600 ft 2 per pail.
- Limitations
- Use DecoSeal only when surface and ambient temperatures are above 40°F (4°C) and below 100°F (38°C) during application and drying period.
- Re-Sealing may be required based on exposure to extreme elements.
- Not intended for substrates exposed to hydrostatic pressure, periodic or continuous water immersion
- Store Decoplast materials in a cool, dry place.
- Sloped surfaces: Refer to Decoplast details.
- DecoSeal should not be used on weather-exposed horizontal or below grade surfaces or where immersion in water may occur.
- Do not apply DecoSeal to frozen surfaces.
Properties
- Technical Data
Value | Units | Test Method / Conditions | |
Volatile Organic Compounds | max. 50 | g/l | — |
Regulatory & Compliance
- Compliance
This product complies with US EPA (40 CFR 59) and South Coast AQMD (Rule 1113) VOC emission standards for architectural coatings.
Safety & Health
- Health & Safety
Health Precaution - Decoplast Decoseal is water-based. As with any chemical construction product, exercise care when handling.
- Warning - Causes eye and skin irritation.
Safety Precaution - Wash hands thoroughly after handling. Wear protective gloves/protective clothing/eye protection/face protection.
First Aid
- Eye Contact - Immediately flush eyes with plenty of water for at least 15 to 20 minutes. Ensure adequate flushing of the eyes by separating the eye lids with fingers. Get immediate medical attention.
- Skin Contact - Immediately wash skin with plenty of soap and water for at least 15 to 20 minutes, while removing contaminated clothing and shoes. Get medical attention if irritation develops or persists.
- Inhalation - If inhaled, remove to fresh air. If not breathing give artificial respiration or give oxygen by trained personnel. Seek medical attention immediately.
- Ingestion - If swallowed, do not induce vomiting. Call a physician or a poison control center immediately. Never give anything by mouth to an unconscious person.
Spills - Contain and collect in an appropriate container. Uncured material may be removed with water.
Disposal - Dispose of in accordance with local, state or federal regulations.
Warning - Keep container closed when not in use. Keep out of the reach of children. Not for internal consumption. For industrial use only.
Packaging & Availability
- Packaging Type
- Packaging
5 gal pail (19L) 40 lbs. / 18 kg per pail
- Availability
Available in Matte or Gloss finish.
Storage & Handling
- Shelf Life
2 years from date of manufacture when properly sealed and stored.
- Storage
DecoSeal must be stored at a minimum of 50ºF (10ºC) in tightly sealed containers protected from weather and out of direct sunlight.