Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features and Benefits
- 10-year warranty
- 100% acrylic roof coating
- Renews most roofing substrates
- Expands and contracts with the roof
- Long-lasting protection and reflectivity
Applications & Uses
- Markets
- Compatible Substrates & Surfaces
- Recommended Uses
- Metal, single ply, smooth BUR, modified bitumen, polyurethane foam, concrete, existing asphaltic and elastomeric roof coatings and other approved surfaces
- Not for use on roof shingles
- Dry Time
Exposure to rain or heavy due: 4-6 hours. Between coats and before roof traffic: 24 hours minimum.
- Coverage Rate
Metal: 70-100 sq. ft/gallon
Apply the following substrates with Kool Seal® Elastomeric Base Coat at 50-100 sq. ft/gallon, followed by Kool Seal® Elastomeric Finish Coat at the following rates:
Single Ply: 50-70 sq. ft/gallon
Smooth BUR/Modified Bitumen: 50-70 sq. ft/gallon
Polyurethane Foam: 50-70 sq. ft/gallon
Concrete: 50 sq. ft/gallonDo Not Thin.
- Surface Preparation
Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. Surface must be power washed (minimum 2,000 psi) to remove dirt, and other foreign matter that could prevent proper adhesion.
Surfaces must be completely dry prior to coating.
Important: Where ponding water conditions persist beyond 48 hours, roof drains or other corrective measures must be installed to eliminate water buildup prior to coating the roof. Repair all cracks, breaks, open seams and other imperfections with Kool Seal® Storm Patch® Acrylic Patching Cement and Kool Seal® Storm Patch® Polyester Fabric. Apply Kool Seal® Storm Patch® Acrylic Rust Primer to existing rusted areas.
- Application
Do not apply below 50°F (10°C) or when rain is forecast. Applications during periods of low temperature and high humidity will extend dry time. Keep From Freezing.
Thoroughly mix product prior to application. Airless spray or apply with a low-nap roller or broom at the appropriate coverage rate. Allow adequate drying time between coats. Two coats recommended.
- Clean Up
Warm, soapy water
Properties
- Color
- Typical Properties
Value | Units | Test Method / Conditions | |
VOC | max. 50 | g/L | - |
Solids (by Volume) | 43 - 47 | % | - |
Solids (by Weight) | 56 - 60 | % | - |
Safety & Health
- Cautions
- Use with adequate ventilation.
- Keep out of the reach of children.
- Use a NIOSH-approved respirator when necessary.
- Do not take internally.
- In case of ingestion, Call a Physician immediately. Do not induce vomiting.
- If splashed in the eyes, flush thoroughly with clean water for a minimum of 15 minutes. Call a Physician immediately. May cause irritation to the skin. If brought into contact with the skin, wash thoroughly with soap and water. Seek medical attention if redness or irritation occurs. Avoid breathing vapors and spray mist. Reseal container after each use. Wear protective clothing, gloves and goggles.
Packaging & Availability
- Packaging Type
- Ordering Information
Part Number Color/Size KS0063600-16 White (0.9 Gallon)
KS0063600-20 White (4.75 Gallon Pail)