Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Advantages
- Offers advanced stain protection
- Built with Microban® antimicrobial technology -
- Continuously inhibits the growth of bacteria, mold and mildew on the sealed surface.
- Preserves the original look of the surface and is breathable
- Water-based formula - Better for you and the environment
- Low odor, non-flammable and weather resistant -
- For interior and exterior use
- Professional grade
Note: STONETECH Heavy Duty Sealer built with Microban antimicrobial product protection can be combined for use with previous versions of the product to obtain stain protection performance. For antimicrobial product protection, use STONETECH Heavy Duty Sealer with Microban antimicrobial protection.
Applications & Uses
- Markets
- Uses
- Countertops
- Backsplashes
- Floors
- Walls
- Suitable Substrates
- Marble
- Granite
- Quartzite
- Limestone
- Travertine
- Slate
- Bluestone
- Sandstone
- Flagstone
- Saltillo
- Grout
- Installation
Approximate Coverage
- Up to 112 ft2 /pint (10.4 m² /473 mL) / single coat
- Up to 225 ft2 /quart (20.9m² /946 mL) / single coat
- Up to 900 ft2 /gallon (83.6 m² /3.8 L) / single coat
- Up to 4500 ft2 / 5 gal (418 m² / 18.9 L) / single coat
Surface Preparation
Read entire label before using. Use only as directed. Always test in a small inconspicuous area with a 24-hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. May also be used as a pre-grout sealer. Make sure surface is clean and free of waxes and coatings. Sealer may be applied to damp surfaces one hour after standing water has been removed. Surface temperature should be between 50°F and 80°F (10°C and 27°C). Ensure that the area is well-ventilated during application and until the surface is dry. Keep children and pets out of the area until treated surface is dry
Directions
- Ensure cap is closed and sealed, and shake well before use.
- Mask off surfaces not intended to be treated.
- Liberally apply an even coat of STONETECH® BulletProof Sealer using a paint pad, roller, brush or low-pressure sprayer.
- Allow sealer to penetrate the surface for 10-15 minutes. During this time, keep the surface wet with sealer, adding more sealer as needed. DO NOT ALLOW SEALER TO COMPLETELY DRY ON THE SURFACE.
- Thoroughly wipe dry the entire surface with clean absorbent towels.
- A second coat may be needed for porous, absorbent surfaces. If a second coat is required, it should be applied within 30-40 minutes from the initial application as directed in steps 3 - 5.
- Should a sealer residue appear, rewet the impacted section of the surface with sealer. Agitate the surface with a white nylon scrubbing pad to loosen residue and wipe dry with a clean, absorbent towel.
- A full cure is achieved in 24-72 hours. Use of the treated surface may resume in 6-8 hours. If use of the surface must resume sooner, cover the treated surface with red rosin paper to protect it until full cure has been achieved.
- Clean tools used during application with water.
Expected Wear
- Up to 5 years on interior surfaces
- Up to 3 years on exterior surfaces
- Maintenance
Highly alkaline, acidic, ammoniated, or abrasive cleaners are not necessary for daily maintenance and may also degrade the STONETECH sealer used, adversely affecting stain resistance. Tile and stone routine cleaning with a neutral pH cleaner such as STONETECH Stone & Tile Cleaner is recommended. For tough or difficult to remove soil use STONETECH KlenzAll™ Cleaner, a nylon scrubbing pad or a long handled stiff bristle brush. Please note: Prior to using any cleaning material on a tile, stone, etc. installation, test a discrete area or scrap piece of tile to insure desired results.
Properties
- Odor
- Mild
- Working Properties
- Physical Properties
| Value | Units | Test Method / Conditions | |
| Full Cure | 24 - 72 | hours | - |
| Surface Traffic | 6 - 8 | hours | - |
| Value | Units | Test Method / Conditions | |
| pH | 9 - 11 | - | - |
| Specific Gravity | 1.009 | - | - |
Technical Details & Test Data
- Technical Data
VOC/LEED Product Information
- <400 g/L (excluding water) for EPA Purposes
- <120 g/L (including water) for LEED and U.S. State purposes (Low Solids Coating)
Packaging & Availability
- Packaging
US
- ST309-1202: 2oz (59ML) Sample Bottle - 12 / case, NOT For Resale
- ST309-1216: Pint /16oz (473ML) Bottle - 12 / case
- ST309-0624: 24oz (709ML) Spray Bottle - 6 / case
- ST309-0632: Quart /32oz (946ML) Bottle - 6 / case
- ST309-0401: Gallon /128oz (3.8L) Bottle - 4 / case
- ST309-0105: 5 Gallon (18.9L) Bottle - 1 unit
CANADA
- ST352-1216: Pint /16oz (473ML) Bottle - 12 / case
- ST352-0632: Quart /32oz (946ML) Bottle - 6 / case
- ST352-0401: Gallon /128oz (3.8L) Bottle - 4 / case
- ST352-0105: 5 Gallon (18.9L) Bottle - 1 unit
Storage & Handling
- Shelf LIfe
Factory sealed containers of this product are guaranteed to be of first quality for two (2) years if stored at temperatures >50°F (10°C) and <90°F (32°C).
- Storage and Handling Instructions
Avoid prolonged exposure to vapors. Use in a well-ventilated area. Do not ingest. Avoid contact with eyes and skin. Keep Out of The Reach of Children. Do not freeze or store above 100°F (38°C). Do not mix with other chemicals. Do not release to natural waterways.