Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Product Highlights
- Environmental approvals are simplified because NOCOR E6 is nitrite, barium, boron, phenol, and phosphate free
- NOCOR E6 is low foaming, for use in lowpressure spray washers and flow coating operations. Dip application is also a good way to apply this product
- An excellent choice where both ferrous and/or copper alloy parts are being processed
- NOCOR E6 has a moderate pH, is practically odorless, and is nonflammable for improved safety
- Working concentration ranges from 4% - 16% which translates into much lower cost than traditional straight oil/solvent products
- Protect metal parts from rust and oxidation for up to six months with super-concentrated, very economical Master STAGES™ emulsion corrosion inhibitors. Barium-free with very low V.O.C. content, environmentally friendly Master STAGES emulsion corrosion inhibitors are built for lowpressure spray, immersion, and dip applications.
- Additional Information
- Industrial Use Only
- Consult Master Fluid Solutions before using on any metals or applications not specifically recommended.
- This product should not be mixed with other metalworking fluids or metalworking fluid additives, except as recommended by Master Fluid Solutions, as this may reduce overall performance, result in adverse health effects, or damage the machine tool and parts. If contamination occurs, please contact Master Fluid Solutions for recommended action.
- Master STAGES™ is a trademark of Master Chemical Corporation d/b/a Master Fluid Solutions.
Applications & Uses
- Markets
- Application Method
- Use Level
- 4.0 - 16.0 %
- Application Guidelines
- NOCOR E6 must be diluted with water by the user. There are no special mixing requirements. DI or RO water will produce a more stable emulsion and better rust inhibition, but "soft" tap water may be used. The normal dilution range is from 4% - 16% product in water.
- NOCOR E6 working baths should not be heated above 120°F as this will reduce its effectiveness. Drying with hot air up to 250°F produces good results.
- Concentrations below 4% are not recommended.
- NOCOR E6 must be allowed to dry completely prior to stacking or packaging parts and must be drained from blind holes and recesses.
- Since carry over of cleaners into the NOCOR E6 bath can reduce resistance to wash-off, and so reduce protection, you should insert a plain water rinse between washing and NOCOR E6 application if possible
- Product Applications
Applications : Corrosion inhibition, dip, flow coating, and low-pressure spray washing
Metals : Cast iron, copper alloys, ferrous metals, and steels
Industries : Automotive- Mixing Instructions
- Recommended usage concentration in water: 4.0% - 16.0%.
- To help ensure the best possible working solution, add the required amount of concentrate to the required amount of water (never the reverse) and stir until uniformly mixed.
- Recommended Metalworking Concentrations
Design concentration range : 4.0% - 16.0%
Properties
- Odor
- Mild (Concentrate)
- Physical Properties
| Value | Units | Test Method / Conditions | |
| Flash Point (Concentrate) | max. 300 | °F | ASTM D93-08 |
| pH (Typical Operating as Range) | 8.5 - 10.0 | - | - |
| Coolant Refractometer Factor | 1.2 | - | - |
| V.O.C. Content | 133 | g/l | ASTM E1868-10 |
| Cleaner Conductivity Factor | 0.01 | - | - |
Regulatory & Compliance
- Product Compliance
NOCOR E6 is free of barium, borates, nitrites, phenols, and phosphate
Technical Details & Test Data
- Test Data
Concentration by Conductivity
Packaging & Availability
- Packaging
- 1-gallon jug
- 5-gallon pail
- 54-gallon drum
- 270-gallon tote