Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- B/L Description
Paint and Related Material NOIBN Protect from Freezing
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Unique Advantages
- Low VOC/No HAPs option for SB VOC regulations
- Self-sealing eliminates steps
- Yellowing-resistant finish
- High chemical and moisture resistance
- Quick hardness development
- Available in flat, dull, satin and gloss sheens in clear and white/opaque bases
Note: Arroyo 2K WB Polyurethane needs to be catalyzed with C38277 catalyst. See product data sheet for mixing instructions.
Applications & Uses
- Markets
- Application Area
- Application Method
- Uses
For use on kitchen and bathroom cabinets, dormitory, household, and office furniture. Also, for use on toys, paneling, and display fixtures.
- Application
Application Procedure
Sand wood using 220 grit sandpaper, as required. If water borne stain is used, it is recommended to lightly scuff sand dry stained surface with fine scotch-brite before applying ARROYO® 2K WB POLYURETHANE PIGMENTED TOPCOAT CLEAR to reduce possible grain raise from stain. ARROYO® 2K WB POLYURETHANE PIGMENTED TOPCOAT CLEAR can be used as a self-sealing system or V140959 Arroyo® 1K Sealer can be used as a first sealer coat. Apply 2 coats (3 if self-seal) of WB Polarion at 3-5 wet mils per coat. Sand with 320, Fre-cut (no fill) type sandpaper between first and second coat. Sand with 320 and then very fine scotch brite between second and third coat. Always sand just prior to recoating. The total dry film build should be at least 3 mils and should not exceed 6 dry mils. To obtain the highest level of chemical resistance, let product cure for a minimum of 7 to 10 days before use in a harsh chemical environment, i.e. bar or tabletop use.
Note: Hot spray application is not recommended. Apply using only stainless steel or plastic spray equipment. Before application, surface and air temperature should be a minimum of 65°F.
Mixing and Catalyzing
ARROYO® 2K WB POLYURETHANE PIGMENTED TOPCOAT CLEAR must be catalyzed with 2K WB Polyurethane Catalyst C38277-DP at the ratio of 100 parts base product to five parts catalyst (5% catalyst by volume or weight). Weigh or measure catalyst then pour into product while stirring. Let the mixture sit with a loosely covered lid for a minimum of 5-10 mins to release CO2 created during catalyzation and avoiding air entrapment. The viscosity of the product should now be thin enough to spray. Once catalyzed the product has up to 4 hours pot-life under normal conditions. If spraying your final coat when near the end of the pot-life you may want to filter the product before spraying to avoid any contamination caused by previous handling of product or exposure to open air.
Equipment Clean Up
- All equipment should be flushed with warm water, water/alcohol or Gun & Line Cleaner Concentrate GLC10 immediately after use.
- A subsequent flush with alcohol will ensure all moisture is removed from equipment.
- Catalyzed material mixture can be left to sit out and dry solid, then throw out.
Surface Preparation
- New Work: Remove any dirt, grease or other construction contamination from surface. Sand wood as required – 220 grit, scotch brite water borne stain.
- Old Work: Remove any dirt, grease, or other contamination from surface. Sand well to improve adhesion.
Reduction
No reduction is required. After catalyzing, product viscosity may drop 5-10 seconds. If required, small amounts of clean water may be used for specific equipment. Over-thinning due to the high solids nature of this product can cause sags. Thinning should be limited to 5% maximum.
Caution
- THESE PRODUCTS ARE DESIGNED FOR PROFESSIONAL USE ONLY.
- Use only after all safety information is understood.
- Refer to the Safety Data Sheet (SDS) or Material Safety Data Sheet (MSDS) for additional information.
Notes
The information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application that are not known or under our control, M.L. Campbell cannot make any warranties as to the end result. Thank you for using M.L. Campbell Wood Finishing products.
Properties
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Weight Per Gallon | 8.41 - 8.81 | lbs/gal | - |
| Viscosity (Ford #4 At 77°F) | 30 - 40 | ” Ford 4 | - |
| Solids by Weight | 31.0 - 35.0 | % | - |
| Solids by Volume | 28.5 - 32.5 | % | - |
| Theoretical Coverage (At 1 Mil Dry) | 484 - 494 | sq. ft. per gallon | - |
| Flash Point | 497 - 501 | °F | PMCC |
| Sheen (Flat) | 7.0 - 10.0 | - | 60° Glossmeter |
| Sheen (Dull) | 13 - 17 | - | 60° Glossmeter |
| Sheen (Satin) | 33 - 37 | - | 60° Glossmeter |
| Sheen (Gloss) | 90+ | - | 60° Glossmeter |
| Packaged VOC | 137.5 | g/l | - |
| Photochemically Reactive | No | - | - |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (At 77°F) | 40 - 45 | minutes | - |
| Sanding Dry (At 77°F) | 60+ | minutes | - |
| Stacking Dry (At 77°F) | min. 10 | hours | - |
Regulatory & Compliance
- Compliance
GREENGUARD certified.
Packaging & Availability
- Packaging/Shipping
- Available Units: Gallons and Pails. (Restrictions for shipments of freezable materials.)
Storage & Handling
- Shelf Life and Storage
- Freezable – Store in airtight containers.
- Protect from temperature extremes.
- Shelf life is 18 months