Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- DOT Classification
Flammable Liquid Red Label UN 1263
- B/L Description
Paint UN 1263 3 PG II
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Uses
Designed for finishing furniture, interior paneling, trim or other wood finishing uses where the fast dry, high build and final smooth appearance are important.
- Application
Application Procedure
Apply one coat of DesignRclassic Lacquer Sealer at 3-5 wet mils maximum. Sand with 220 to 320 grit sandpaper before applying 1-2 coats of DesignRclassic Lacquer Clear Topcoat.
Note: Hot spray application is not recommended. If hot spray equipment is used, temperature setting should never be over 110°F.
Mixing
Shake or stir well before and during use.
Equipment Clean Up
- Use lacquer thinner or VC16936 Fast Reducer VOC Exempt to clean up all equipment.
- Dispose of dirty solvent and cleaning rags in a safe and approved manner.
- Solvent or lacquer soaked rags should be stored in a water filled, closed containers prior to disposal
Surface Preparation
- New Work: Remove any dirt, grease or other contamination and sand as required.
- Old Work: Strip old finishes completely and remove all contaminants from the surface. Make sure surface is dry. Finish as new work.
Reduction
No reduction is required; however, small amounts of lacquer thinner may be used if required for specific equipment. If blushing occurs use up to 5% M.L. Campbell C1621 Care Reducer or 1-3% M.L. Campbell C16336 BC Retarder.
Testing
Due to the wide variety of substrates, surface preparation methods, application methods, and environments, customers should test the complete system for adhesion and compatibility under their conditions prior to full-scale application.
Caution
- THESE PRODUCTS ARE DESIGNED FOR PROFESSIONAL USE ONLY.
- Use only after all safety information is understood.
- Refer to the Safety Data Sheet (SDS) or Material Safety Data Sheet (MSDS) for additional information.
Notes
The information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application that are not known or under our control, M.L. Campbell cannot make any warranties as to the end result. Thank you for using M.L. Campbell Wood Finishing products.
Properties
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Weight Per Gallon | 7.2 - 7.6 | lbs/gal | - |
| Viscosity (Ford #4 At 77°F) | 12 - 17 | sec | - |
| Solids by Weight | 21 - 25 | % | - |
| Solids by Volume | 14 - 18 | % | - |
| Theoretical Coverage (At 1 Mil Dry) | 256.0 | sq. ft. per gallon | - |
| Flash Point | 8.0 | °F | PMCC |
| Packaged VOC | 623.0 | g/l | - |
| Photochemically Reactive | No | - | - |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (At 77°F) | 10 - 15 | minutes | - |
| Sanding Dry (At 77°F) | 15 - 30 | minutes | - |
| Stacking Dry (At 77°F) | 4.0 | hours | - |
Regulatory & Compliance
- Compliance
HAPs Compliant, GREENGUARD® Certified.
Packaging & Availability
- Packaging/Shipping
- Available Units: Gallons, Pails and Drums.
Storage & Handling
- Shelf Life and Storage
- Package life is (3) three years - Store in a cool dry area in the original sealed containers.
- Do not store around any source of flames or sparks.
- Spills should be cleaned up with non-sparking tools and inert absorbent material.