Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
- DOT Classification
Flammable Liquid Red Label UN 1263
- B/L Description
Paint UN 1263 3 PG II
Features & Benefits
- Labeling Claims
Applications & Uses
- Markets
- Applications
- Compatible Substrates & Surfaces
- Uses
Designed for finishing furniture, interior paneling, trim or other wood finishing uses where the fast dry and high build advantages may be of benefit.
- Application
Application Procedure
Do not apply material too heavy (3 to 5 wet mils per coat is recommended). Too much coating weight may cause recoating and durability problems. A good finishing system can be developed by applying 1 coat of NC SL Sealer or QD SL Sealer at 3-5 wet mils. Sand with 220 to 320 grit sandpaper. Then, apply 1 or 2 coats of NC SL Topcoat. Product should be applied at temperatures of at least 68°F.
Note: Note: Hot spray application is not recommended. If hot spray equipment is used, temperature settings should never be over 110°F.
Mixing
Shake or stir well before and during use.
Equipment Clean Up
- Use M.L. Campbell Fast Reducer VOC Exempt VC16936 to clean up all equipment.
- Dispose of dirty solvent and cleaning rags in a safe and approved manner.
- Solvent or lacquer-soaked rags should be stored in water-filled, closed containers prior to disposal.
Surface Preparation
- New Work: Remove any dirt, grease or other contamination and sand as required. If desired, apply WoodSong II stain, as directed by the specific M.L. Campbell Product Information sheet, prior to finishing
- Old Work: Strip old finishes completely and remove all contaminants from surface. Make sure surface is dry. Finish as new work. If cratering develops on old work, Fish Eye Killer may remedy this problem, if the contamination is not severe
Reduction
No reduction is required; however, small amounts of M.L. Campbell Fast Reducer VOC Exempt VC16936 or Medium Reducer VOC Exempt VC1681 may be used if required for specific equipment. If blushing occurs use M.L. Campbell Slow Retarder VOC Exempt VC1671. IMPORTANT – M.L. Campbell VOC Exempt Reducers and Retarders are compliant and will not increase VOC levels in VOC compliant coatings.
Caution
- THESE PRODUCTS ARE DESIGNED FOR PROFESSIONAL USE ONLY.
- Use only after all safety information is understood.
- Refer to the Safety Data Sheet (SDS) or Material Safety Data Sheet (MSDS) for additional information.
Testing
Due to the wide variety of substrates, surface preparation methods, application methods, and environments, customers should test the complete system for adhesion and compatibility under their conditions prior to full-scale application.
Notes
The information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application that are not known or under our control, M.L. Campbell cannot make any warranties as to the end result. Thank you for using M.L. Campbell Wood Finishing products.
Properties
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Weight Per Gallon | 7.78 - 8.18 | lbs/gal | - |
| Viscosity (Ford #4 At 77°F) | 10.0 - 15.0 | sec | - |
| Solids by Weight | 19 - 23 | % | - |
| Solids by Volume | 13.5 - 17.5 | % | - |
| Theoretical Coverage (At 1 Mil Dry) | 240 - 260 | sq. ft. per gallon | - |
| Flash Point | 40.0 | °F | PMCC |
| Sheen (Dull) | 13.0 - 17.0 | - | 60° Glossmeter |
| Sheen (Satin) | 33 - 37 | - | 60° Glossmeter |
| Sheen (Gloss) | 85+ | - | 60° Glossmeter |
| VOC | 255 - 265 | g/l | - |
| Photochemically Reactive | No | - | - |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (At 77°F) | 15 - 20 | minutes | - |
| Sanding Dry (At 77°F) | 30 - 35 | minutes | - |
| Stacking Dry (At 77°F) | 8.0 | hours | - |
Packaging & Availability
- Packaging/Shipping
- Available Units: Gallons and Pails.
Storage & Handling
- Shelf Life and Storage
- Package life is one year - Store in a cool dry area in the original sealed containers.
- Do not store around any source of flames or sparks.
- Spills should be cleaned up with non-sparking tools and inert absorbent material.
- If stored at temperatures below 30°F (0°C), this product may gel. If so, warming to room temperature will restore it to usable condition.