Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
- DOT Classification
Flammable Liquid Red Label UN 1263
- B/L Description
Paint UN 1263
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Unique Advantages
- Formaldehyde free solvent borne
- Meets AWI chemical and moisture resistance standards for conversion varnish
- GREENGUARD Certified
- Low odor
- Mar and scratch resistant
- Excellent adhesion on both closed and open grain surfaces
- Exceptional film build and depth of image
- Quick dry to sand and recoat times
- Increased production from fast pack and stack times
- Ready to spray and easy to apply with any equipment
Applications & Uses
- Markets
- Application Area
- Cure Method
- Uses
EnviroMax formulas were specifically designed with ease of use on interior wood furniture, millwork, kitchen and bathroom cabinets exposed to moisture, heat, and household chemicals.
- Application
Application Procedure
EnviroMax is formulated to be a self-sealing system. Always agitate thoroughly before application. Apply 2-3 coats at 3-6 wet mils on sanded substrate. The second or third coat should be applied after complete drying of the previous coat. For easy sanding between coats use 280-320 grit fre-cut (no-fill) sandpaper. Always sand prior to recoating. The total dry film build should be at least 2.5 mils and should not exceed 5.0 dry mils. EnviroMax should be applied when temperatures in the spray room are at a minimum of 68°F (20°C).
Note: Hot spray application is not recommended. If hot spray equipment is used, temperature settings should never be over 110°F or 43° C.
Mixing
Mix well before using. Material may separate during long-term storage.
Equipment Clean Up
- Use Standard Lacquer Thinner C16036 or VC16036 Fast Reducer VOC Exempt to clean up all equipment.
- Dispose of dirty solvent and cleaning rags in a safe and approved manner.
- Solvent or lacquer-soaked rags should be stored in water-filled, closed containers prior to disposal.
Surface Preparation
- New Work: Remove any dirt, grease or other contamination and sand as required. If desired, apply WoodSong II stain as directed by the specific M.L. Campbell Product Information (PI) Sheet, prior to finishing.
- Old Work: Strip old finishes completely and remove all contaminants from the surface. Make sure surface is dry. Finish as new work.
Reduction
No reduction is required; however, small amounts of M.L. Campbell Standard Lacquer Thinner C16036 or Care Reducer may be used if required for specific equipment. If blushing occurs use M.L. Campbell C161 1 Care Retarder.
Caution
- THESE PRODUCTS ARE DESIGNED FOR PROFESSIONAL USE ONLY.
- Use only after all safety information is understood.
- Refer to the Safety Data Sheet (SDS) or Material Safety Data Sheet (MSDS) for additional information.
Notes
The information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application that are not known or under our control, M.L. Campbell cannot make any warranties as to the end result. Thank you for using M.L. Campbell Wood Finishing products.
Properties
- Physical Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Weight Per Gallon | 7.75 - 8.15 | lbs/gal | - |
| Viscosity (Ford #4 At 77°F) | 20 - 30 | sec | - |
| Solids by Weight | 29.5 - 33.5 | % | - |
| Solids by Volume | 22 - 26 | % | - |
| Theoretical Coverage (At 1 Mil Dry) | 360 - 410 | sq. ft. per gallon | - |
| Flash Point | 55.0 | °F | PMCC |
| Sheen (Dull) | 13.0 - 17.0 | - | 60° Glossmeter |
| Sheen (Satin) | 33 - 37 | - | 60° Glossmeter |
| Sheen (Semi-Gloss) | 63 - 67 | - | 60° Glossmeter |
| Sheen (Gloss) | 80+ | - | 60° Glossmeter |
| Packaged VOC (Less Exempt Solvents) | 629.0 | g/l | - |
| HAPs | No | - | - |
| Photochemically Reactive | No | - | - |
| Value | Units | Test Method / Conditions | |
| Dry to Touch (At 77°F) | 20 - 25 | minutes | - |
| Sanding Dry (At 77°F) | 40 - 45 | minutes | - |
| Stacking Dry (At 77°F) | 8.0 | hours | - |
Regulatory & Compliance
- Compliance
GREENGUARD Indoor Air Quality Certified.
Packaging & Availability
- Packaging/Shipping
- Available Units: Gallons and Pails.
Storage & Handling
- Shelf Life and Storage
- Shelf life – 24 months
- 60 days after catalyzation: Store in a cool, dry area in the original sealed containers.
- Do not store around any source of flames or sparks.
- Spills should be cleaned up with non-sparking tools and inert absorbent material.
- If stored at temperatures below 30°F (0°C), this product may gel.
- If so, warming to room temperature will restore it to useable condition