Products

Addisil™ 8101 silicone adhesive is a one-component heat curable silicone adhesive sealant which will bond to many substrates without a primer and which will cure rapidly at elevated temperatures. This product has a very long working time at room temperature and will not cure completely until exposed to elevated temperatures.Addisil™ 8101 is a gray thixotropic materialKey Features and Benefits One component product - no mixing required Room temperature storage Very fast cure at elevated temperature (in a range of 110°C to 230°C) Primerless adhesion to many types of substrates (e.g. PBT, PA, phenolic resins, copper, nickel, aluminum, stainless steal, brass, ceramic and glass) No formation of cure by-products; low linear shrinkage Non-corrosive to metals and sensitive substrates Excellent dielectric properties Outstanding performance over a wide temperature range Service temperature -50°C to 250°C.

Addisil™ 6100 silicone adhesive is a one-component heat curable silicone adhesive sealant which will bond to many substrates without a primer and which will cure rapidly at elevated temperatures. This product has a very long working time at room temperature and will not cure completely until exposed to elevated temperatures.Addisil™ 6100 is a black, thixotropic paste, which can be applied to vertical or overhead surfaces.Key Features and Benefits One component product - no mixing required Room temperature storage Fast cure at elevated temperature (in a range of 140 °C to 230 °C) Primerless adhesion to many types of substrates (e.g. glass, enamel, aluminum, ceramic) No formation of cure by-products Non-corrosive to metals Good performance over a wide temperature range Service temperature -50 °C to 250 °C.

Addisil™ 6300 silicone coating is a one-component heat curable silicone coating, which will bond to many substrates without a primer and which will cure rapidly at elevated temperatures. This product has a very long working time at room temperature and will not cure completely until exposed to elevated temperatures.Addisil™ 6300 is a white, flowable material, which can be applied on a textile by knife over roll.Compliance with FDA regulationsKey Features and Benefits One component product - no mixing required Room temperature storage Fast cure at elevated temperature (in a range of 140 °C to 230 °C) Primerless adhesion to many types of substrates No formation of cure by-products Non-corrosive to metals Good performance over a wide temperature range.

Addisil™ 6101 Momentive Performance Material's Silicone adhesive is a one-component heat curable silicone adhesive sealant which will bond to many substrates without a primer and which will cure rapidly at elevated temperatures. This product has a very long working time at room temperature and will not cure completely until exposed to elevated temperatures.Addisil™ 6101 silicone adhesive is a black, thixotropic paste, which can be applied to vertical or overhead surfaces.Key Features and Benefits One component product - no mixing required Room temperature storage Very fast cure at elevated temperature (in a range of 110°C to 230°C) Primerless adhesion to many types of substrates (e.g. aluminum, copper, stainless steel, glass, enamel, ceramic) No formation of cure by-products; low linear shrinkage Non-corrosive to metals and sensitive substrates Outstanding performance over a wide temperature range Service temperature -50°C to 250°C.

The Addisil™ 480 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacture.

Addisil™ 160 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 70 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacturing.

Addisil™ 2070 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

Addisil™ 2060 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

Addisil™ 150 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 70 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacturing.

The Addisil™ 450 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacture.

The Addisil™ 452 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf-life of 6 months for the single component if stored appropriately Very long pot life of 2 to 4 weeks for the mixed components.

The Addisil™ 442 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf-life of 6 months for the single component if stored appropriately Very long pot life of 2 to 4 weeks for the mixed components.