Products

Tufel™ III rubber series are biocompatible(1), two component silicone rubber compounds. 92506 and 92656 are 50 and 65 durometer addition curable silicone elastomers that offer low compression set and high resilience with no post bake required for most applications. The combination of these properties may lead to longer service life in highly mechanical applications. The 92506 and 92656 elastomers can be used to produce extruded and calendered parts with excellent permanent set resistance and should be considered for applications such as peristaltic pump tubing, gaskets and seals.Key Features and Benefits Low compression set Excellent elastic memory Biocompatible(1) No post baking required for most applications Low volatile bases minimize porosity Peroxide-free cure system Broad processing window High output rates Tight surface cure Non-blooming Translucency Low hysteresis Potential Applications Healthcare Consumer Goods General Industrial.

LIM™ 6050-D2 liquid silicone rubber is a 2-component product formulated for use in liquid injection molding to high performance elastomeric parts. It is clear, but easily pigmentable with Momentive Performance Materials masterbatch colors. LIM6050-D2 offers convenient 1:1 mix ratio, high tear strength, and easy release from molds. Cure time is rapid, generally 10 to 40 seconds (@ 150-205°C) depending upon part size, configuration, and molding temperature.Key Features and BenefitsLIM6050-D2 liquid silicone rubber is distinguished by the following properties: High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration, and molding temperature Wide range of molding temperatures: 150°C (302°F) to 205°C (400°F) Excellent release from metal molds Potential ApplicationsThe combination of excellent clarity, tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Baby bottle nipples Connector inserts Seals Flexible mounts Valves Sports goggles Masks Health care equipment Camera parts Coating metal rolls.

LIM™ 6045 by Momentive Performance Materials is comprised of Liquid Silicone Rubber. It is commonly used as Molding Resin for a variety of applications. It is available in Liquid form.

Silplus™ 60 EX is a heat cured silicone rubber base compound that is an excellent candidate to consider for use in extrusion, press-molding injection and calendaring. Silplus™ 60 EX heat cured silicone may be considered for use in a wide variety of high quality applications such as high durometer tubes and profiles.Key Features and Benefits excellent extruding processability good mechanical properties high green strength easily blendable versatile Potential ApplicationsBecause of its outstanding properties, Silplus™ 60 EX heat cured silicone is an excellent candidate to consider for use in most types of extrusion and calendaring applications.

LIM™ 6040-D2 liquid silicone rubber is a 2-component product formulated for use in liquid injection molding to high performance elastomeric parts. It is clear, but easily pigmentable with Momentive masterbatch colors. The combination of excellent tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Mechanical parts such as connector inserts, seals, flexible mounts, and valve parts can be made readily from LIM6040-D2 liquid silicone rubber.Key Features and Benefits High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration, and molding temperature Wide range of molding temperatures: 150°C (302°F) to 205°C (400°F) Excellent release from metal molds The combination of excellent clarity, tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Baby bottle nipples Connector inserts Seals Flexible mounts Valves Sports goggles Masks Health care equipment Camera parts Coating metal rolls.

Silopren™ Matrix 70 and 80 two-component liquid silicone rubber for injection molding processes contain polymeric fibers, which help reinforce molded articles while maintaining LSR's excellent processing properties.Key Features and Typical BenefitsVulcanizates consisting of Silopren™ Matrix LSR are distinguished by the following properties: High thermal stability Excellent stability and flexibility at low temperatures Good rubber-like properties High modulus High stability to ozone and ultraviolet light Outstanding resistance to aging Excellent dielectric behavior over a wide range of temperatures Not readily combustible, does not melt or drip Easily pigmentable with LSR color pastes Potential ApplicationsBecause of its outstanding properties, Silopren™ Matrix LSR is an excellent candidate to consider for use in the following elastomeric articles: Membranes Pressure hoses Exhaust hangers Watchbands Belts.

LIM™ 6040 liquid silicone rubber is a 2-component product formulated for use in liquid injection molding to high performance elastomeric parts. It is clear, but easily pigmentable with Momentive Performance Materials masterbatch colors.Key Features and Benefits High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration, and molding temperature Wide range of molding temperatures: 1500C (3020F) to 2050C (4000F) Excellent release from metal molds Potential ApplicationsThe combination of excellent clarity, tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Baby bottle nipples Connector inserts Seals Flexible mounts Valves Sports goggles Masks Health care equipment Camera parts Coating metal rolls.

LIM™ 6030 liquid silicone rubber is a 2-component product formulated for use in liquid injection molding to high performance elastomeric parts. It is clear, but easily pigmentable with Momentive masterbatch colors. The combination of excellent tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Mechanical parts such as connector inserts, seals, flexible mounts, and valve parts can be made readily from LIM 6030 liquid silicone rubber.Key Features and Benefits High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration, and molding temperature Wide range of molding temperatures: 150°C (302°F) to 205°C (400°F) Excellent release from metal molds Potential Applications sports goggles and masks health care equipment camera parts coating metal rolls.

The Addisil™ 480 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacture.

LIM™ 6071 is the next generation in 70-durometer liquid silicone rubber. It is a two-component product formulated for use in liquid injection molding to produce high performance parts. It is clear, but easily pigmentable with Momentive masterbatch colors. The combination of excellent tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Mechanical parts such as connector inserts, seals, flexible mounts, and valve parts can be made readily from LIM6071 liquid silicone rubber.Key Features and Benefits High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration and molding temperature Wide range of molding temperatures: 150°C (302°F) to 232°C (450°F) Excellent release from metal molds High Bayshore resilience Potential Applications Sports goggles and masks Health care profiles Camera parts Metal roll coatings.

Addisil™ 160 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 70 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacturing.

Tufel™ II Silicone Rubber Compounds 94206 and 93306 are 20 and 30 durometer low volatile fast-cure addition cured silicone elastomers for extrusion and calendering. They may be used by themselves or blended to intermediate durometers. Applications include extruded tubings, profiles and calendered sheets.Key Features and Benefits LV Bases Minimize Porosity and Post Cure Totally Peroxide-Free Cure System Broad Processing Window High Output Rates High Tear Strength Tight Surface Cure Non-blooming Translucency.

Tufel™ III rubber series are biocompatible(1), two component silicone rubber compounds. 92506 and 92656 are 50 and 65 durometer addition curable silicone elastomers that offer low compression set and high resilience with no post bake required for most applications. The combination of these properties may lead to longer service life in highly mechanical applications. The 92506 and 92656 elastomers can be used to produce extruded and calendered parts with excellent permanent set resistance and should be considered for applications such as peristaltic pump tubing, gaskets and seals.Key Features and Benefits Low compression set Excellent elastic memory Biocompatible(1) No post baking required for most applications Low volatile bases minimize porosity Peroxide-free cure system Broad processing window High output rates Tight surface cure Non-blooming Translucency Low hysteresis Potential Applications Healthcare Consumer Goods General Industrial.

Tufel™ II 94706 are 40-70 durometer low volatile fast-cure addition cured silicone elastomers for extrusion and calendering. They may be used by themselves or blended to intermediate durometers. Applications include extruded tubings, profiles and calendered sheets.Key Features and Benefits LV Bases Minimize Porosity and Post Cure Totally Peroxide-Free Cure System Broad Processing Window High Output Rates High Tear Strength Tight Surface Cure Non-blooming Translucency.

The Addisil™ 472 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf-life of 6 months for the single component if stored appropriately Very long pot life of 2 to 4 weeks for the mixed components.

The Addisil™ 452 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf-life of 6 months for the single component if stored appropriately Very long pot life of 2 to 4 weeks for the mixed components.

TheAddisil™ IND 2060 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

Silopren™ Matrix 70 and 80 two-component liquid silicone rubber for injection molding processes contain polymeric fibers, which help reinforce molded articles while maintaining LSR's excellent processing properties.Key Features and Typical BenefitsVulcanizates consisting of Silopren™ Matrix LSR are distinguished by the following properties: High thermal stability Excellent stability and flexibility at low temperatures Good rubber-like properties High modulus High stability to ozone and ultraviolet light Outstanding resistance to aging Excellent dielectric behavior over a wide range of temperatures Not readily combustible, does not melt or drip Easily pigmentable with LSR color pastes Potential ApplicationsBecause of its outstanding properties, Silopren™ Matrix LSR is an excellent candidate to consider for use in the following elastomeric articles: Membranes Pressure hoses Exhaust hangers Watchbands Belts.

Addisil™ 2050 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

The Addisil™ IND 1070 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80° Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months as of manufacturing date Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

The Addisil™ 442 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf-life of 6 months for the single component if stored appropriately Very long pot life of 2 to 4 weeks for the mixed components.

The Addisil™ IND 1050 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80° Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months as of manufacturing date Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

The Addisil™ IND 2050 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

Tufel™ II 94506 are 40-70 durometer low volatile fast-cure addition cured silicone elastomers for extrusion and calendering. They may be used by themselves or blended to intermediate durometers. Applications include extruded tubings, profiles and calendered sheets.Key Features and Benefits LV Bases Minimize Porosity and Post Cure Totally Peroxide-Free Cure System Broad Processing Window High Output Rates High Tear Strength Tight Surface Cure Non-blooming Translucency.

The Addisil™ 2080 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

The Addisil™ 450 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacture.

The Addisil™ 440 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacture.

Addisil™ 2060 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

The Addisil™ 482 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf-life of 6 months for the single component if stored appropriately Very long pot life of 2 to 4 weeks for the mixed components.

The Addisil™ 140 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 70 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months from date of manufacturing.

The Addisil™ IND 1080 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80° Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months as of manufacturing date Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

The Addisil™ 462 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 40 and 80 Shore A for medical applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. The series is especially suitable for the manufacture of extruded transparent tubing and profiles for use in healthcare applications.Key Features and Benefits- High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf-life of 6 months for the single component if stored appropriately Very long pot life of 2 to 4 weeks for the mixed components.

LIM™ 6050 liquid silicone rubber is a 2-component product formulated for use in liquid injection molding to high performance elastomeric parts. It is clear, but easily pigmentable with Momentive masterbatch colors. The combination of excellent tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Mechanical parts such as connector inserts, seals, flexible mounts, and valve parts can be made readily from LIM6050 liquid silicone rubber.Key Features and Benefits High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration, and molding temperature Wide range of molding temperatures: 150C (302F) to 205C (400F) Excellent release from metal molds Potential Applications sports goggles and masks health care equipment camera parts coating metal rolls.

Tufel™ II 94606 are 40-70 durometer low volatile fast-cure addition cured silicone elastomers for extrusion and calendering. They may be used by themselves or blended to intermediate durometers. Applications include extruded tubings, profiles and calendered sheets.Key Features and Benefits LV Bases Minimize Porosity and Post Cure Totally Peroxide-Free Cure System Broad Processing Window High Output Rates High Tear Strength Tight Surface Cure Non-blooming Translucency.

LIM™ 6061 is the next generation in 60-durometer liquid silicone rubber. It is a two-component product formulated for use in liquid injection molding to produce high performance parts. It is clear, but easily pigmentable with Momentive masterbatch colors. The combination of excellent tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Mechanical parts such as connector inserts, seals, flexible mounds, and valve parts can be made readily from LIM6061 liquid silicone rubber.Key Features and Benefits High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration and molding temperature Wide range of molding temperatures: 150°C (302°F) to 232°C (450°F) Excellent release from metal molds High Bayshore resilience Potential Applications sports goggles and masks health care profiles camera parts coating metal rolls.

Addisil™ 2070 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.