Products

Tufel™ III rubber series are biocompatible(1), two component silicone rubber compounds. 92506 and 92656 are 50 and 65 durometer addition curable silicone elastomers that offer low compression set and high resilience with no post bake required for most applications. The combination of these properties may lead to longer service life in highly mechanical applications. The 92506 and 92656 elastomers can be used to produce extruded and calendered parts with excellent permanent set resistance and should be considered for applications such as peristaltic pump tubing, gaskets and seals.Key Features and Benefits Low compression set Excellent elastic memory Biocompatible(1) No post baking required for most applications Low volatile bases minimize porosity Peroxide-free cure system Broad processing window High output rates Tight surface cure Non-blooming Translucency Low hysteresis Potential Applications Healthcare Consumer Goods General Industrial.

LIM™ 6045 by Momentive Performance Materials is comprised of Liquid Silicone Rubber. It is commonly used as Molding Resin for a variety of applications. It is available in Liquid form.

Silopren™ Matrix 70 and 80 two-component liquid silicone rubber for injection molding processes contain polymeric fibers, which help reinforce molded articles while maintaining LSR's excellent processing properties.Key Features and Typical BenefitsVulcanizates consisting of Silopren™ Matrix LSR are distinguished by the following properties: High thermal stability Excellent stability and flexibility at low temperatures Good rubber-like properties High modulus High stability to ozone and ultraviolet light Outstanding resistance to aging Excellent dielectric behavior over a wide range of temperatures Not readily combustible, does not melt or drip Easily pigmentable with LSR color pastes Potential ApplicationsBecause of its outstanding properties, Silopren™ Matrix LSR is an excellent candidate to consider for use in the following elastomeric articles: Membranes Pressure hoses Exhaust hangers Watchbands Belts.

Tufel™ III rubber series are biocompatible(1), two component silicone rubber compounds. 92506 and 92656 are 50 and 65 durometer addition curable silicone elastomers that offer low compression set and high resilience with no post bake required for most applications. The combination of these properties may lead to longer service life in highly mechanical applications. The 92506 and 92656 elastomers can be used to produce extruded and calendered parts with excellent permanent set resistance and should be considered for applications such as peristaltic pump tubing, gaskets and seals.Key Features and Benefits Low compression set Excellent elastic memory Biocompatible(1) No post baking required for most applications Low volatile bases minimize porosity Peroxide-free cure system Broad processing window High output rates Tight surface cure Non-blooming Translucency Low hysteresis Potential Applications Healthcare Consumer Goods General Industrial.

TheAddisil™ IND 2060 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

Silopren™ Matrix 70 and 80 two-component liquid silicone rubber for injection molding processes contain polymeric fibers, which help reinforce molded articles while maintaining LSR's excellent processing properties.Key Features and Typical BenefitsVulcanizates consisting of Silopren™ Matrix LSR are distinguished by the following properties: High thermal stability Excellent stability and flexibility at low temperatures Good rubber-like properties High modulus High stability to ozone and ultraviolet light Outstanding resistance to aging Excellent dielectric behavior over a wide range of temperatures Not readily combustible, does not melt or drip Easily pigmentable with LSR color pastes Potential ApplicationsBecause of its outstanding properties, Silopren™ Matrix LSR is an excellent candidate to consider for use in the following elastomeric articles: Membranes Pressure hoses Exhaust hangers Watchbands Belts.

Addisil™ 2050 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

Silplus™ 30 AS, 30 duro hardness heat cured silicone rubber compound for compression molding processes, offers a good anti-static property to silicone rubber products.Key Features and Typical Benefits Good anti-static property Colorable translucent appearance Excellent mechanical properties and heat resistance Excellent processability Easy coloring Potential Applications Mobile jacket, keypad cover, keypad watch Consumer goods, novelty, accessory Industry roller, rubber sheet Automobile parts.

The Addisil™ IND 1070 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80° Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months as of manufacturing date Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

The Addisil™ IND 1050 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80° Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months as of manufacturing date Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

The Addisil™ IND 2050 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

The Addisil™ 2080 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

Addisil™ 2060 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

The Addisil™ IND 1080 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80° Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months as of manufacturing date Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

Addisil™ 2070 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test.

Silopren™ LSR 2670 FC by Momentive Performance Materials is comprised of Silicone Elastomer. It is commonly used as Molding Resin for a variety of applications in Aerospace, Automotive and Aviation. It is available in Liquid form.

The Addisil™ IND 1060 E series is a one-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80° Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits High transparency, no yellowing Excellent mechanical properties Dry, non-stick surface Odorless during processing and in its application Fast curing One-component, ready to use Shelf life of 3 months as of manufacturing date Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

The Addisil™ IND 2070 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.

The Addisil™ IND 2080 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications.Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odorless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations.