Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- Extra Coverage
- Cost Effective
- Flexural Strength
- Grout In 6 Hours
Applications & Uses
- Markets
- Applications
- Application Method
- Compatible Substrates & Surfaces
- Suitable Substrates
- Concrete/Cement Render
- Brickwork/Blockwork (Cement Rendered)
- Fiber Cement Sheets (Primed)
- Plasterboard (Primed)
- Over Morgan Waterproof Membrane
- Application On
INTERIOR/EXTERIOR
Walls Floors - Suitable Tiles
- Natural Stone
- Bicottura
- Monocottura
- Fully Vitrified
- Porcelain
- Precautions
Morflex Plus is unsuitable for:
- Bonding moisture sensitive green marble
- Bonding to MDF board or timber & wax impregnated wood (Our technical advice - sheet with fiber cement boards)
- Bonding to substrates subject to constant water immersion such as swimming pools
- Applications
Substrate Preparation & Expansion Joints
All substrates to be tiled must be flat and true, free from oil, dirt, grease or any other contaminants. Very porous substrates should be primed with Morgan Universal Primer. Incorporate expansion joints in accordance with AS 3958.
- Concrete: New concrete must be allowed to cure for 6 weeks and should have a wood float finish. Use Floor Prep to acid etch an adhesive key into concrete finished with a steel float.
- Cement Render: Render to be left with a wood float finish and allowed to cure for 7 days.
- Fiber Cement Sheets: Fiber cement sheets must be primed with Morgan Universal Primer and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions.
- Plasterboard : Plasterboard must be fixed as per manufacturer’s instructions. Jointing compound must be primed with Morgan Universal Primer.
Open Time
Morflex Plus has an open time of approximately 30 minutes, which can be shortened to just a few minutes by the action of sun, wind, high temperatures or highly absorbent surfaces. Dampening or priming the substrate prior to tiling prolongs the open time of the adhesive. Tilers need to constantly check that the adhesive has not formed a surface skin and is still fresh to touch. Adhesive with a surface skin must be always removed and discarded.
Mixing
Add Morflex Plus to clean water at a ratio of 20kg to 6 liters of water. Mix the adhesive to a smooth paste free from lumps by using a drill that has a speed lower than 300 rpm, or mix by hand. Slacken the adhesive and re-mix after 5 minutes.
Application, Tools & Adjustability Time
Always install the tiles in accordance with AS 3958 1:1991 and ensure the backs of the tiles are free of dust. Spread Morflex Plus evenly across one square meter at a time with a 6mm notched trowel for walls and a 10mm notched trowel for floors. The choice of trowel should be governed by the depth of the knobs, grooves or ridges on the back of each tile and the evenness of the substrate. Lay the tiles with a fair pressure and at right angles to the adhesive notched pattern. The final bed of adhesive should be between 2mm and 4mm. Wall tiles should have a finished joint width of 2mm - 4mm and floor tiles should have a finished joint width of 3mm - 6mm. Tiles can be adjusted for approximately 15 minutes after laying.
Coverage
20kgs of Morflex Plus will cover approximately 12 square meters with a 6mm notched trowel for walls and approximately 10 square meters with a 10mm notched trowel for floors.
Cure Time
Morflex Plus cures in approximately 24 hours at 23°C and 50% relative humidity. High density substrates or tiles and temperatures during installation below 10°C will significantly increase the cure time.
Clean Up
Remove excess Morflex Plus from the grout joints after 30 minutes and clean the tiles with a damp cloth or sponge. Tools and hands can be cleaned with water while the adhesive is still wet.
Joint Grouting
Depending on environmental conditions, commence grouting after approximately 6 hours. Use Regular or Superior Grout for grout joints between 3mm to 6mm. Morgan Slate & Quarry Grout should be used for joint sizes between 6mm to 20mm. Use Aquapoxy, a three component acid resistant epoxy grout, if the joints are required to have a good chemical resistance. Grout Add may also be mixed with Regular Grout to impart extra flexibility, reduce porosity and increase water resistance.
- Joint Grouting Precautions
Do not use excessive amounts of water during mixing or initial cleaning as this will cause irregular color finishes and also weaken the grout. Do not mix the grout with an electric drill above 300 rpm as this can entrap air into the mix causing grout to dry soft and powdery or with unsightly pin holes in the surface. All grouts should be damp cured for 48 hours. Refer to the australian standard as 3958 part 1 section 5.7.3.
Regulatory & Compliance
- Certifications & Compliance
- Regulatory & Compliance
Specification Clause
The wall & floor adhesive shall be Morgan Morflex Plus - a high performance tile adhesive complying with all relevant Australian & International technical standards.
Morgan Quality Policy Statement
Morflex Plus is manufactured and distributed to a quality system based on ISO 9001:2000. Morflex Plus is guaranteed for 15 years when installed to the guidelines of AS 3958 Part 1 & 2, 2007 and in conjunction with written technical information supplied by Morgan Ceramic Tile Adhesives.
Packaging & Availability
- Packaging Type
- Packaging
Morflex Plus is available in 20kg bags.
Storage & Handling
- Pot Life
Morflex Plus has a pot life of approximately 2 hours at 23°C and 50% relative humidity.
- Shelf Life
Twelve months if stored in a dry & elevated position in the original factory sealed packaging.