Products

Murpec® SP is a High wear resistance; High compressive strength; Good slide properties; Good continuous temperature behavior. Production based on PEEK-SP.

Murinit® SP [FS], thanks to the low fiber content and integrated solid lubricant, this high-performance material offers an excellent combination of good slide and wear behavior, high strength, and dimensional stability – even at high temperatures. Murinit® SP also has a good resistance to chemicals and hydrolysis.Production based on PPS-SP.

"Since the 1950s, Material ""S""® has been tried and tested a thousand times over for a wide range of applications in power engineering and conveyor technology Material ""S""® is based on virgin, ultra- high molecular weight low pressure polyethylene and significantly exceeds the requirements of DI n 16972. Original Material ""S""® is one of the most successful groups of materials in the industrial plastics sector. In particular, Original Material ""S"" green® has established itself as a branded product in the plastics sector. It is used in all applications where a technical, high- performance plastic is required. Original Material ""S"" green® is synonymous with excellent slide properties, high wear resi - stance, and a long lifetime." Production based on PE-UHMW SG 1.2.

This material has the same properties as Muralen® but also has an antimicrobial effect.Production based on PE-UHMW SG 2.1.

"Muralen® is based on high molecular weight polyethylene (PE-HMW) and is ideally suited for use in applications that require the generally impressive material properties of polyethylene. However, it is only used in cases where the excellent slide and wear resistance properties of Original Material ""S""® are not required. Because of its great cut, impact, and shock resistance, this material is often used to make underlays for cutting and punching machines and for ram guards."

This material combines the excellent properties of the Murylon® range with additional high tensile and burst strength, increased wear resistance, and a lower level of moisture absorption than Murylon® B. Production based on PA66.

The use of this plastic saves energy and improves the efficiency of your machines thanks to its low friction resistance. The sliding friction coefficient is reduced by up to 50 percent with this material – and so too the energy consumption for the drive power required. This plastic offers real energy-saving potential. Thanks to the additive used, Original Material ”S” ® plus+ LF ESD is electrically conductive, enabling voltage to be dissipated at maximum speed with the same maximum friction resistance. A member of the S plus family Production based on PE-UHMW SG 1.1.

"Original Material ""S"" plus+® FP [FS]® is a new technical plastic that completely meets the requirements of the food sector for the detectability of plastic foreign bodies in foods. ""FP"" stands for ""food protect"" and embodies two vital properties: This product is both food-safe and metal-detectable. Metallic foreign bodies in foodsare safety detected by metal detectors and removed. However, plastic particles from plant components can be problematic. Thanks to the use of additives in Original Material ""S"" plus+® FP [FS], all commonly used metal detectors in the food industry can now detect and remove plastic particles. Furthermore, in the case of this material, particles even smaller than the required size for the detectability of metal (3 mm) can be found and removed: Particles of only 2mm in size (see the illustration) have been detected without any problems in tests." A member of the S plus family Production based on PE-UHMW SG 1.1.

Thanks to its extremely low electrical resistances, Original Material "S" plus+® ESD is an optimum conductor. Full voltage dissipation for earthed components at maximum speed enables spark-free, safe work. This material provides a cost-effective alternative to carbon-filled PTFE.A member of the S plus family Production based on PE-UHMW SG 1.2.

Original Material "S" plus+® AB contains special substances that prevent the growth of bacteria and other microbes at the same time as protecting the environment and people. The material is thus ideally suited for use when manufacturing and processing foods. It can reduce the growth of microbes on surfaces by between 99.96 to 99.99% in comparison with materials with no special additives. This means that it can virtually eradicate unpleasant smells and the formation of biofilm. Original Material "S" plus+® AB combines antibacterial properties with exceptional characteristics of the "S" plus+® family. A member of the S plus family Production based on PE-UHMW SG 1.2.

In comparison with other thermoplastics, Murpec® has an exceptionally low thermal expansion coefficient. This property provides optimum dimensional stability and means that dimensions do not change even if used in wet environments. Because of the high glass transition temperature, the material’s rigidity and strength are retained almost in their entirety even at high temperatures. Murpec® materials are extremely resistant to deformation and exceptionally abrasion-proof. Production based on PEEK.

This material is ideally suited for use in the food sector and medical industry. As a fluorinated plastic, Murinyl® is exceptionally resistant to chemicals, hydrolysis, and sterilization. Moreover, the properties of the material change very little even at high service temperatures and after long-term exposure to UV radiation, meaning that Murinyl® is ideally suited for a wealth of applications both inside and outside. Production based on PVDF.

This material is used for applications that involve manufacturing and transportation at high pressure. The balance quantity of micro glass beads in Original Material "S" plus+® GB provide the combined benefits of extremely high molecular weight polyethylene and glass. The glass beads that protrude from the surface provide a rounded and hard sliding surface. A member of the S plus family Production based on PE-UHMW SG 1.1.

Murylon® B natural has the best impact resistance of all Murylon materials. This material is especially suited for use in machine construction thanks to an excellent combination of mechanical properties. Production based on PA6.

Original Material "S"® black has the same properties as Original Material "S"® green/natural. In addition, it is also electrostatically conductive due to the addition of additives.Production based on PE-UHMW SG 1.2.