Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Application Method
- Application Characteristics
Mix Ratio : Mix 2 parts N-8055A with 1 part H2OB by volume.* See comments. Mixture
Reducer : Water – 1 part by volume can be used to thin to spray viscosity if necessary
Cleaning Solvent: Water
Pot Life : 4 hours at78ºF. Increases in temperature may reduce pot life.- Recommended Primers
Substrate Recommended Primer
Aluminum/Galvanized Steel/Stainless Steel B-875/T-63 or N-8564A/N-8564B Wash Primers and N-1088A/B, N-1981A/B or N-8901A/B Epoxy Primers.
Ductile or Gray Iron Castings N-1981A/B, N-8901A/B or N-1088A/B
Plastics Due to the wide variety of plastic/fiberglass substrates, system performance should be tested and confirmed on actual substrate.
Previously Painted Surfaces Surface should be intact and sound. All loose and flaking material removed and bare spots primed with an appropriate primer. An area should be tested with the coating to assure compatibility.
Steel N-5751M2 Zinc Rich Epoxy, N-1088A/B, N-1981A/B or N-8901A/B Epoxy Primers.
Wood Due to the wide variety of wood substrates, system performance should be tested and confirmed on actual substrate.
- Application Equipment
Conventional Electrostatic Air Pressure: N/A Fluid Pressure: N/A Cap: N/A
Tip:Conventional Spray Air Pressure: 10 - 30 psi Fluid Pressure: 20 - 40 psi Cap: N/A
Tip: 1.4 – 1.6HVLP Spray Air Pressure: 10 psi Fluid Pressure: 20 - 40 psi Cap: N/A
Tip: 1.4 – 1.6Air Assisted Airless Air Pressure: 20 - 40 psi Fluid Pressure: 1000 psi "Cap: N/A
Tip: 0.011 - 0.013”"Airless Pressure: 3000 psi Tip: 0.013” Brush and Roll : Use for touch up only, the use of natural china chip bristle brushes or ¼” maximum nap mohair type rollers is highly recommended to limit the amount of orange peel.
*Note: The above parameters are to be used as a guideline only. Customer specific equipment may require a different set-up
- Surface Preparation
Do not apply if the application surface temperature is below 45°F (7°C) or above 110°F (43°C), or if the surface temperature is within 5°F of the dew point. It is highly recommended that sound practices as set forth by SSPC or NACE be followed when preparing a substrate for painting. At a minimum the surface should be clean of all grease, dirt, oil, rust and foreign material that would be detrimental to proper adhesion and desired performance of the coating system being applied.
- Application Characteristics
Dry Times (Touch, 77°F at 50% RH) 15 - 30 minutes Dry Times (Recoat Anytime, 77°F at 50% RH) Anytime - Cleaning and sanding may be needed Dry Times (Hard, 77°F at 50% RH, Hard) 1 - 2 hours Dry Times (Through Dry, 77°F at 50% RH) max. 2 hours Full Cure (77°F at 50% RH) 1 week
Properties
- Color
- Physical Properties
Value Units Test Method / Conditions Gloss (85º) max. 3.5 - - Volume Solids (Mixed Unreduced) 43.6 - 47.6 % - Weight Solids (Mixed Unreduced) 52.8 - 56.8 % - Weight Per Gallon {(A)10.0 (H2OB)} 8.6 - 9.2 lbs/gal - Theoretical Coverage (1 mil dft Mixed Unreduced) 731.0 sq ft/gal - VOC (Mixed) max. 1.8 lbs/gal mixed - Recommended Film Thickness (DFT) 1.8 - 2.0 mil - Viscosity (A Component ) 55 - 80 KU - Substrate Tested Zinc Phosphate Pretreated Steel - - Salt Spray {(B117) Q-Steel panels prepared at a combined primer/top coat system of 3.5 - 4.5 dft (Dependent on Primer Selection)} 336 - 1000 hours - Humidity (Dependent on Primer Selection) 336 - 1000 - - QUVA (340) 1000.0 hours - Pencil Hardness 2H - - Impact Direct/Indirect 40.0 inch-pounds - Dry Heat Resistance Pass - - Crosshatch Adhesion Pass 5 - -
Regulatory & Compliance
- Quality Standards
Technical Details & Test Data
- Chemical Resistance
MEK, 100 Double Rubs Pass Lubricating and Cutting Oils Pass Hydraulic Fluids Pass Water Immersion Pass 10% Hydrochloric Acid Pass 10% Acetic Acid Pass 10% Sodium Hydroxide Pass Gasoline Pass
Storage & Handling
- Shelf Life & Storage Conditions
Shelf life (protected from atmospheric moisture): 12 months from the date of manufacture. This product must be stored in accordance with local, state, and national regulations. Preferred storage conditions: Keep containers in a dry space with adequate ventilation.