Products

NP130 is a woven glass fabric combined with halogenated epoxy resin system. NP130 is produced to printed circuit board quality standards. It is flame retardant, and meets the requirements of MIL-I-24768/27, Type GEE-F and IEC-60893-3-2 EP GC 202.

NP572 is a high strength, medium weave glass epoxy laminate that retains a minimum of 50 percent of its room temperature flexural strength when tested at 150ºC and its Tg is guaranteed to be 180°C or greater. Typical applications include electrical equipment subjected to elevated temperatures. NP572 is certifiable to IEC 60216-3, IEEE STD 98-2002 and ASTM D2304 for Class H insulation in electrical devices. NP572 is also certifiable to MIL-I-24768/3, Type GEB.

Canvas phenolic laminate with molybdenum disulphide added as a solid lubricant. This material has improved wear properties under certain conditions. Material is semi-conductive to electricity and should no be used where this is detrimental to the application.

Hot punching general-purpose phenolic grade. Mechanical properties approach those of NP610 with improved electrical properties and moisture resistance. Certification to IEC standard is pending.

A paper-base laminate with low phenolic resin content for hard, flat surfaces. This material is most commonly used for drill entry material in the PCB industry.

MC511FR is a high strength, medium weave glass epoxy laminate that retains a minimum of 50 percent of its room temperature flexural strength when tested at 150ºC. Typical applications include structural applications when used in elevated temperatures. MC511FR also complies with MIL-I-24768/28, Type GEB-F. Certification to IEC standard is pending.

Room temperature punching and shearing grade up to 0.125″ thick. NP615 is more flexible with lower mechanical properties than NP611. NP615 is produced with high resin content melamine impregnated surfaces to give the resulting laminate better arc resistance. Intended for applications where electrical and moisture requirements are secondary.

MC511SN, StatNot™, is a static dissipative epoxy, woven glass based material with excellent control of the static dissipative properties. This material is used where static dissipation is required from surfaces to surface of the composite, in the x, y and z directions.

Paper reinforced phenolic grade with controlled conductivity. NP843 has mechanical strength similar to NP611. It has conductive surfaces only.

A paper-base laminate with low phenolic resin content for hard, flat surfaces. It is typically hot punched for numerous low voltage electrical applications of less than 250 volts where the material is not subjected to high humidity.

Lower cost paper phenolic NEMA Grade XP. NP660 uses natural kraft paper without pigmented cover sheet. It is a warm to hot punching material. It is available in natural and black only, without a pigmented cover, only. Certification to IEC standard is pending.

Grade MC320LE is a fine weave bleached cotton phenolic composite that has excellent machining characteristics and low moisture absorption. Applications include marine applications, terminal boards and parts requiring medium strength and excellent electrical characteristics. MC320LE meets or exceeds the requirements of MIL-I-24768/13 and ASMT F2953-12 Type FB. Certification to IEC standard is pending.

Low cost room temperature punching grade with mechanical and electrical properties similar to NP612. This version is made with pigment cover plies on the surface.

Hot punching grade with excellent electrical properties and low moisture absorption. Major application is for punched parts for switches and other insulation applications requiring high electrical strength in applications where either moisture is present or in areas of high humidity.

NP510A is a woven glass fabric composite combined with epoxy resin system. It is engineered to provide NEMA grade FR-4 properties. This material contains bromine on the epoxy resin backbone. NP510A is certifiable to MIL-I-24768/27, Type GEE-F.

MC511AF is a high strength, medium weave glass epoxy laminate that retains a minimum of 50 percent of its room temperature flexural strength when tested at 150ºC. Typical applications include insulation in power generation equipment and other structural applications when used in elevated temperatures. MC511AF is certifiable to MIL-I-24768/3, Type GEB.

Woven glass fabric, melamine resin laminate. NP509 is very hard, flame resistant, machining grade with excellent electrical properties in high humidity conditions. NP509 has high physical strength and excellent arc resistance. Meets MIL-I-24768/1 type GME, MIL-I-24768/8 type GMG and IEC 60893-3-3-MF GC 201.

Phenolic paper based grade for mechanical applications. Good tensile, compressive and flexural strength. Primarily a machining material, but may be hot punched up to .093" thick. NP610 meets MIL-I24768/12 Type PBM, ASTM D709 Type X and IEC 60893-3-4 PFCP 201.

Manufactured with a cotton fabric and phenolic resin, NP310E is easy to machine and possesses lower moisture absorption and enhanced electrical properties. NP310E meets or exceeds the requirements of MIL-I-24768/14.

NP511 consists of a woven glass fabric combined with high temperature epoxy resin system. NP511 has excellent mechanical strength and electrical properties from cryogenic to elevated temperatures. Continuous operating temperature is 175°C. This material meets NEMA G-11, MIL-I-24768/3, Type GEB and IEC-60893-3-2 EP GC 203.

MC511A is a high strength, glass epoxy laminate that is specially formulated to meet power generation producer’s exacting standards where higher strength at elevated temperatures are required. MC511A is certifiable to MIL-I-24768/3, Type GEB, IEC-60893-3-2 EP GC 203 and is halogen free to meet the European restrictions.

Woven glass fabric with high temperature phenolic resin. Good flexural, compressive and impact strengths at elevated temperatures. It is capable of continuous operation at 175°C. NP504 has excellent creep resistance because of the phenolic resin system. Meets MIL-I-24768/18 GPG. For NFPA 130 data please reference document NP504 Additional Data Sheet - NFPA 130. Certification to IEC standard is pending.

NP613 is constructed from electrical grade of kraft paper and a specially modified epoxy resin system. It is designed to be used in tap changers, coil support plates and terminal panels for transformers and their accessories.

NP629 is a paper-phenolic high-pressure laminate and intended primarily for mechanical applications, but is suitable for electrical applications as well. The electrical properties are not quite as good as those of NP630. Certification to IEC standard is pending.

NP511EM is constructed of a woven glass fabric combined with a high temperature, easy machining epoxy resin. It has excellent mechanical strength and electrical properties at elevated temperatures. The continuous operating temperature is 190°C, in mechanical applications. This material meets NEMA G-11 and MIL-I-24768/3, Type GEB.

Paper phenolic grade with better electrical properties than NP612. NP625 requires slightly more heat to shear and punch than NP612. Certification to IEC standard is pending.

A paper-base laminate with low phenolic resin content for hard, flat surfaces. This material is normally used in the printed circuit board industry as a backup for the drilling operation. However, it is also used in other industries for tooling stock because of its ease of machining and good dimensional stability.

Room temperature punching and shearing paper phenolic grade up to .125" thick. NP612 is more flexible with lower mechanical properties than NP611, and is intended for applications where electrical and moisture requirements are of secondary importance. NP612 meets the requirements of MIL-I-24768/20.

NP643 is constructed from an electrical grade kraft paper and a high temperature specially modified epoxy resin system. It is designed to be used in tap changers, coil support plates and terminal panels for transformers and their accessories.

NP630 is a fine machining grade with excellent electrical properties and moisture resistance. It has low cold flow with good dimensional stability.

Hot punching general-purpose phenolic grade. Mechanical properties approach those of NP610 with improved electrical properties and moisture resistance. NP611 meets the requirements of IEC60893-3-4-PF CP 201.

MC507U is a utility grade, glass fabric combined with a silicone resin system. It can be substituted for NEMA G-7, in most heating, appliance insulation and some bearing applications. MC507U has excellent strength and electrical properties. MC507U complies with MIL-I-24768/17 – GSG, with the exception of some specific electrical properties. Certification to IEC standard is pending.

Canvas phenolic laminate with molybdenum disulfide lubricant. The mechanical properties are slightly lower than NP310. NP313 is used for lubricity in the composite when carbon (graphite) cannot be used because of conductivity.

NP130HF is a woven glass fabric composite combined with epoxy resin system, which is engineered to provide better physical properties than standard NEMA FR-4. It is significantly more dimensionally stable than NP130 or NP510A because of its low resin content. The main application for NP130HF is for “bed-of-nails” probe boards used for printed circuit board testing, and other structural applications. Certification to IEC-60893-3-2 EP GC 202

RT500M is composed of a medium weight glass fabric combined with an epoxy resin system. RT500M combines excellent electrical characteristics with very good physical properties. Electrical properties maintained in high humidity conditions. It also complies with MIL-I-24768/2, Type GEE and ASTM D709 Type IV Grade G-10. RT500M is not flame resistant. Certification to IEC standard is pending.

Grade RT507 has good electrical properties under humid conditions, superior heat resistance, and superior arc resistance. Typical applications include heating appliance insulation, welding equipment nozzle insulation, heat barriers and specialty bearing applications. RT507 also complies with MIL-I-24768/17, Type GSG and ASTM D709 Type IV Grade G-7.