Products

Nylene Specially formulated nylon 6 molding resin possessing outstanding flow characteristics Ideally suited for applications requiring high flow properties and resistance to cracking Optimum processing conditions should provide a melt temperature of 450 - 470°F at nozzle

Nylene High viscosity nylon copolymer with high impact resistance and superior flexibility Optimized with good melt strength for high line speeds in thin wall sections 2415 HSSP BK is one of a family of grades specifically designed for the convoluted tubing used n the Automotive and Electrical industry, but can also be used for other extrusions and some molded parts.

Nylene Plasticized, high residual monomer resin designed for extrusion applications requiring excellent flexibility, high strength and good abrasion resistance Applications include flexible tubing, cable jacketing, and mono-filament extrusion such as fish line and netting, sewing thread, and weaving thread Optimum processing conditions should permit for a melt temperature of approximately 450°F at the die.

Nylene Unreinforced nylon 6/6 molding resin Has the high heat and chemical resistance characteristic of nylon 6/6 materials, combined with high flow and easy molding Suitable for a variety of applications, such as clips, fasteners, levers, bushings, and other uses where heat, chemical, and wear resistance are required

Nylene Unreinforced general purpose polycarbonate injection molding grade Has the high impact resistance and heat resistance typical of polycarbonate Available in water white, blue tint, black, and pre-colored Suitable for such applications as housings and enclosures, brackets, connectors and other typical polycarbonate type uses

Nylene General purpose, 20 % glass fiber-reinforced poly(phenylene ether) (PPE) alloy Areas of application include water contact areas such as impellers and pump housings Suitable for applications such as motor housings which require high modulus and distortion temperature

Nylene Unreinforced heat-stabilized nylon 6/6 molding resin Has the high heat and chemical resistance characteristic of nylon 6/6 materials, combined with high flow and easy molding Suitable for a variety of applications, such as clips, fasteners, levers, bushings, and other uses where heat, chemical, and wear resistance are required

Nylene Duratel MF3 is a high-viscosity acetal co-polymer. Duratel MF3 has slightly higher toughness than standard MF9, and parts molded with MF3 should have thicker wall sections and shorter flow lengths to accommodate the higher viscosity. MF3 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Vexel™ B12U by Polymeric Resources Corporation is comprised of Polybutylene Terephthalate. It is commonly used as Molding Resin for a variety of applications in Automotive.

Please contact Custom Resins Group for additional information.

Nylene Duratel MF9 is an unreinforced general purpose acetal co-polymer. Duratel MF9 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF9 issuitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Vexel™ B12GF45 SA by Polymeric Resources Corporation is comprised of Polybutylene Terephthalate. It is commonly used as Molding Resin for a variety of applications.

Nylene General purpose un-reinforced nylon 6 injection molding resin. High flow characteristics at minimal processing temperatures Suitable for applications in both thin and heavy sections that require typical nylon characteristics and easy molding

Nylene Unreinforced nucleated heat-stabilized nylon 6/6 molding resin Has the high heat and chemical resistance characteristic of nylon 6/6 materials, combined with nucleation for faster part set-up Suitable for a variety of applications, such as clips, fasteners, levers, bushings, and other uses where heat, chemical, and wear resistance are required

Nylon 6/12 molding resin with excellent flexibility and lower moisture absorption

Vexel™ B12GF30 SA by Polymeric Resources Corporation is comprised of Polybutylene Terephthalate. It is commonly used as Molding Resin for a variety of applications.

Impact-modified, heat-stabilized, nylon 6/6 molding resin with high impact strength possessing excellent wear properties

Nylene Heat stabilized version general purpose, fast cycling molding resin Crystallization initiators provide fast molding cycles through rapid melt set-up In addition to protection from heat degradation, parts molded from NYLENE 204 HS have better dimensional stability at moisture equilibrium than parts molded from conventional nylon Suitable for molding clip and fasteners, bushings, spacers, and other general purpose applications

Nylene General purpose injection molding resin. Lubricated and nucleated for faster cycle times Suitable for applications such as clips & fasteners, bushings & rollers, and other general purpose uses

Impact-modified, heat-stabilized, nylon 6/6 molding resin with high impact strength Free of silicones, it possesses very low wear properties

Nylene Duratel MF27 is an unreinforced high-flow acetal co-polymer. Duratel MF27 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF27 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Norpex® AX235 by Polymeric Resources Corporation is comprised of Polyphenylene Ether. It is commonly used as Molding Resin for a variety of applications in Automotive.

Vexel™ B50GF30 by Polymeric Resources Corporation is comprised of Polybutylene Terephthalate. It is commonly used as Molding Resin for a variety of applications.

Flame retarded, glass fiber-reinforced poly(butylene terephthalate) (PBT) with good moldability and UL recognition

Please contact Custom Resins Group for additional information.

Nylene Heat stabilized nylon copolymer with 14% glass fiber reinforcement Developed to have excellent light transmittance combined with high strength, stiffness, and resistance to automotive type fluids Suitable for such uses as under-the-hood fluid reservoirs Maximum clarity is achieved by using low mold temperatures

Nylene Low wear 30% glass fiber reinforced nylon 6/6 Provides a low friction and low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced - Suitable for applications such as bushings and bearings, wear plates, caterpillar tracks, and other parts where wear may be an issue

Nylene Recommended for molding applications requiring both maximum durability and toughness Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

Nylene Heat stabilized version of NYLENE 451 recommended for molding - Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

Nylene Glass and ceramic fiber reinforced nylon 6 injection molding material Designed to provide high dimensional stability, very high stiffness, and a hard surface, while maintaining the heat and chemical resistance typical of nylon products Suitable for such uses as valve bodies, pump housings, hydraulic fittings and couplings, and other applications which require this unique set of characteristics

Nylene Duratel MF9 is an un-reinforced general purpose acetal co-polymer. Duratel MF9 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF9 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required

Norpex® AX265 by Polymeric Resources Corporation is comprised of Polyphenylene Ether. It is commonly used as Molding Resin for a variety of applications in Automotive.

Nylene Nylene 5130 PT15 is a low wear 30% glass fiber reinforced nylon 6/6 using Nylene 5130 PT15 provides a low friction and very low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced material. 5130 PT15 is suitable for applications such as bushings and bearings, wear plates, and other parts where high strength with maximum wear resistance is required.

Nylene Low wear 43% glass fiber reinforced nylon 6/6 Provides a low friction and low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced material Suitable for applications such as bushings and bearings, wear plates, caterpillar tracks, and other parts where wear may be an issue