Products

Nylene 50% glass fiber reinforced, heat-stabilized nylon 6 injection molding resin Specifically designed for maximum strength and stiffness while maintaining the heat and chemical resistance typical of nylon 6 resins Suitable for brackets, enclosures, valve bodies, and other uses where maximum strength and stiffness are required

Nylene Heat stabilized version of NYLENE 600 which is a general purpose, medium viscosity, extrusion grade resin used in applications such as rods, slabs, and tubing Other applications include wire jacketing and centrifugal casting which require good dielectric properties, toughness, and fatigue resistance Optimum processing conditions should provide a melt temperature of 480°F - 500°F at the die

Nylene General purpose, medium viscosity, extrusion grade resin used in applications such as rods, slabs, and tubing Other applications include wire jacketing and centrifugal casting which require good dielectric properties, toughness, and fatigue resistance Optimum processing conditions should provide a melt temperature of 481°F - 500°F at the die

Nylene Very high viscosity extrusion resin having an ASTM relative viscosity of 800 Excellent structural strength, durability, and physical properties Good melt strength and good draw-down properties which promote dimensional control for extrusion of pipe, tubing, film, and sheet Particularly recommended for the extrusion of thick slab, large rod stock, and large complex profiles Optimum processing conditions should permit for a melt temperature of 550 - 575°F at the die.

Nylene Unreinforced nylon 6/6 molding resin Has the high heat and chemical resistance characteristic of nylon 6/6 materials, combined with high flow and easy molding Suitable for a variety of applications, such as clips, fasteners, levers, bushings, and other uses where heat, chemical, and wear resistance are required

Nylene General purpose, 20 % glass fiber-reinforced poly(phenylene ether) (PPE) alloy Areas of application include water contact areas such as impellers and pump housings Suitable for applications such as motor housings which require high modulus and distortion temperature

Nylene Unreinforced heat-stabilized nylon 6/6 molding resin Has the high heat and chemical resistance characteristic of nylon 6/6 materials, combined with high flow and easy molding Suitable for a variety of applications, such as clips, fasteners, levers, bushings, and other uses where heat, chemical, and wear resistance are required

Nylene Heat stabilized nylon copolymer with 14% glass fiber reinforcement Developed to have excellent light transmittance combined with high strength, stiffness, and resistance to automotive type fluids Suitable for such uses as under-the-hood fluid reservoirs Maximum clarity is achieved by using low mold temperatures

Nylene General purpose unreinforced nylon 6/10 injection molding grade Has heat and chemical resistance inherent in nylons, while also having the reduced moisture pick-up associated with nylon 6/10 Suitable for clips, bushings, housings, and other uses where moisture pickup may be a concern

Nylene Designed for very fast cycle time molding and parts requiring high flow rates, such as long thin parts or high cavitation tools Low viscosity nylon 6 with special nucleation for rapid part set-up and special flow enhancers to aid in molding Excellent choice for parts such as wire ties, clips, fasteners, bushings and bearings

Nylene 33% glass fiber reinforced nylon 6/10 injection molding grade. Has the high strength and stiffness of reinforced nylon, while also having the reduced moisture pick-up associated with nylon 6/10 Suitable for pump housings, inlet housings, fittings, and other uses where moisture pickup may be a concern

Nylene General purpose injection molding resin. Lubricated and nucleated for faster cycle times Suitable for applications such as clips & fasteners, bushings & rollers, and other general purpose uses

Nylene Nylene 5130 PT15 is a low wear 30% glass fiber reinforced nylon 6/6 using Nylene 5130 PT15 provides a low friction and very low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced material. 5130 PT15 is suitable for applications such as bushings and bearings, wear plates, and other parts where high strength with maximum wear resistance is required.

Nylene Low wear 30% glass fiber reinforced nylon 6/6 Provides a low friction and low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced - Suitable for applications such as bushings and bearings, wear plates, caterpillar tracks, and other parts where wear may be an issue

Nylene Low wear 43% glass fiber reinforced nylon 6/6 Provides a low friction and low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced material Suitable for applications such as bushings and bearings, wear plates, caterpillar tracks, and other parts where wear may be an issue

Nylene Nylon 6 polymer designed for use in extrusion coating and cast and blown filmExcellent grease resistance, toughness, and resistance to abrasion.Films made from Nylene® 615 C have barrier properties against oxygen and aroma typical of nylon 6.Meets the requirements of 21 CFR 177.1500 for food contact.

Nylene Unreinforced nucleated heat-stabilized nylon 6/6 molding resin Has the high heat and chemical resistance characteristic of nylon 6/6 materials, combined with nucleation for faster part set-up Suitable for a variety of applications, such as clips, fasteners, levers, bushings, and other uses where heat, chemical, and wear resistance are required

Nylon 6/12 molding resin with excellent flexibility and lower moisture absorption

Impact-modified, heat-stabilized, nylon 6/6 molding resin with high impact strength possessing excellent wear properties

Nylene Duratel MF9 is an unreinforced general purpose acetal co-polymer. Duratel MF9 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF9 issuitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Nylene Heat stabilized version general purpose, fast cycling molding resin Crystallization initiators provide fast molding cycles through rapid melt set-up In addition to protection from heat degradation, parts molded from NYLENE 204 HS have better dimensional stability at moisture equilibrium than parts molded from conventional nylon Suitable for molding clip and fasteners, bushings, spacers, and other general purpose applications

Nylene Duratel MF9 is an un-reinforced general purpose acetal co-polymer. Duratel MF9 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF9 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required

Nylene Glass and ceramic fiber reinforced nylon 6 injection molding material Designed to provide high dimensional stability, very high stiffness, and a hard surface, while maintaining the heat and chemical resistance typical of nylon products Suitable for such uses as valve bodies, pump housings, hydraulic fittings and couplings, and other applications which require this unique set of characteristics

Nylene Heat stabilized version of NYLENE 451 recommended for molding - Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

Nylene Recommended for molding applications requiring both maximum durability and toughness Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

Nylene Duratel MF3 is a high-viscosity acetal co-polymer. Duratel MF3 has slightly higher toughness than standard MF9, and parts molded with MF3 should have thicker wall sections and shorter flow lengths to accommodate the higher viscosity. MF3 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Nylene Medium viscosity, fast cycle molding resin.Crystallization initiators provide fast molding cycles through rapid melt set-up.Parts molded from NX1440 have better dimensional stability at moisture equilibrium than parts molded from conventional nylon.Suitable for such uses as clips and fasteners, bushings, small levers, gears, and window hardware.Optimum processing conditions should provide a melt temperature of 460 - 480°F at the nozzle.

Nylene Duratel MF27 is an unreinforced high-flow acetal co-polymer. Duratel MF27 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF27 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Impact-modified, heat-stabilized, nylon 6/6 molding resin with high impact strength Free of silicones, it possesses very low wear properties

Nylene General purpose, 30 % glass fiber-reinforced poly(phenylene ether) (PPE) alloy Areas of application include water contact areas such as impellers and pump housings and motor housings which require high modulus and distortion temperature UL recognitized

Nylene Duratel MF9-GF10 is 10% glass fiber reinforced general purpose acetal co-polymer. Duratel MF9-GF10 has increased strength and stiffness over unreinforced acetal. MF9-GF10 retains the chemical resistance and lubricity inherent in acetal materials. This product is suitable for brackets and levers, valve bodies, and other applications requiring this unique blend of properties.

Nylene 43% glass fiber reinforced nylon 6/10 injection molding grade Has the high strength and stiffness of reinforced nylon, while also having the reduced moisture pick-up associated with nylon 6/10 Suitable for pump housings, inlet housings, fittings, and other uses where moisture pickup may be a concern