Knowde Enhanced TDS
Identification & Functionality
- Polymer Name
- Technologies
- Product Families
Features & Benefits
- Materials Features
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Indication of Printable Surface
In order to be avoided blocking phenomenon, typical for both side treated films, one of the treated sides is with higher treatment level. FXCB is usually supplied with main treated layer externally on the rolls, in case of other requirement this must be agreed with our sales representative before order processing.
- Usage Recommendations
- It is recommended that BOPP film should be tempered at operating room temperature for 24 hours before use
- Metalized films should be laminated because the metal layer is not resistant to scratches
- Before printing on metalized films, it is strongly recommended to apply a primer
Properties
- Typical Properties
Value | Units | Test Method / Conditions | |
Average Thickness Deviation | 2.5 | % | — |
Yield | 49.9 - 59.9 | m²/kg | — |
Unit Weight | 13.2 - 23.2 | g/m² | — |
Gloss (45°) | 83 - 87 | — | ASTM D 2457 |
Haze | 1.8 - 2.2 | % | ASTM D 1003 |
Dynamic Coefficient of Friction | 0.22 - 0.32 | — | ASTM D 1894 |
Shrinkage (MD, 120°C, 5 min) | 4.0 | % | BMS TT 0.2 |
Shrinkage (TD, 120°C, 5 min) | 2.0 | % | BMS TT 0.2 |
Sealing Range | 105 - 145 | °C | — |
Seal strength (N/15 mm, 130°C, 1 bar 1sec) | 2 - 3 | — | BMS TT 0.1 |
OTR | 1900.0 | cc/m²/day | ASTM D3985 |
WVTR | 6.5 | gr/m²/day | ASTM F1249 |
Elongation at Break (MD) | 180 - 240 | % | ASTM D 882 |
Elongation at Break (TD) | 50 - 110 | % | ASTM D 882 |
Tensile Strength (MD) | 110 - 170 | MPa | ASTM D 882 |
Tensile Strength (TD) | 210 - 270 | MPa | ASTM D 882 |
Surface Treatment | min. 38 | dynes/cm | ASTM D 2578a |
Regulatory & Compliance
- Food Contact
The BOPP Film complies with all national and international standards and requirements for food contact.
Technical Details & Test Data
- Film Layer Representation
Packaging & Availability
- Packing
Core Diameter Outer Diameter (*) Notes Vertical
152 mm (6') max. 550 mm
max. 700 mm – two or more rows
min. 700 mm – one row76 m (3') Horizontal
152 mm (6') max. 770 mm
76 m (3') (*) In case of no other requirements.
- Tolerances
Weight Tolerance, depending on the order volume Width Tolerance Length Tolerance max. 800 - 1200 ±2 mm ±5 % 900 - 11000 min. 9500 - 10500
Storage & Handling
- Storage and Transportation Terms & Conditions
- Palletizing of goods is done according to customer’s requirements
- The storage of all goods is in dry, covered and clean warehouses
- The transportation of the goods is carried out in dry, covered and clean means of transport
- The recommended temperature of storage/transportation is 10-30°C. If the temperature is not within the recommended limits, the following issues may occur:
- Decrease of dyne level
- Higher haze of the film
- Poor adhesion of the film surface that on a later stage could be an issue for laminating and printing
- Extremely low COF that can trouble further processing
- Excessive humidity can be a reason for film blocking
- Adherence to the above mentioned storage conditions ensures that the film is suitable to be used up to 6 months after production