Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Product Features
- Self-leveling
- 3 day topcoat window
- Excellent for an automotive finish
- Can be topcoated in 60 minutes
- VOC Compliant
Applications & Uses
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Recommended Uses
Delta Sealer is intended for industrial applications; either new build or maintenance. Delta Sealer is suitable for application on properly sanded or sandblasted steel, and properly prepared aluminum, fiberglass, reinforced plastics, existing finishes and polyester fillers. This primer must be topcoated to achieve the best results.
Industries:
- Oilfield & Energy Services
- Well Service vehicles
- Cranes and Construction Equipment
- Automotive
- Trailers & Rolling Stock
- Waste and Recycling Industry
- Garbage Truck
- Mix Ratio
- 4 part by volume of component A
- 1 part by volume of component B
The recommended temperature when mixed is 68-77°F (20-25°C).
- Surface Preparation
Surface must be free of all contaminants such as dust, oil, grease and salt. It is recommended that all steel and other ferrous surfaces be cleaned to a minimum of SSPC-SP6 or mechanically sanded with 180 grit sandpaper.
- Application Method
Delta Sealer can be applied using most spray systems, although electrostatic sprayers are not recommended. Apply a single coat. If a second coat is required allow sufficient flash time between coats (20-30 minutes).
- Spray Gun Setup
Feed Type Fluid Tip Application Pressures (Heel of Gun) Fluid Delivery Siphon Feed 1.4 - 2.0 mm 40 - 50 psi Gravity Feed 1.4 - 2.0 mm 30 - 40 psi Pressure Feed 1.0-1.8 mm 50 - 60 psi 10 - 14 oz/min Air Assist Airless 9 - 13 Thou 1000 - 1800 psi Airless 9 - 13 Thou 1700 - 3000 psi - Spraying Viscosity
Note: Spraying viscosity and thinning will depend on ambient conditions, spray equipment used, and the desired surface finish. Thinning is not typically required.
If required, recommended spraying viscosity is achieved by reducing with one of the following Endura Low VOC Topcoat Reducers. These will maintain VOC compliance of Delta Sealer Low VOC Primer.
VOC content of the following Reducers: (0g/l, 0lbs/gal)
Low VOC Topcoat Reducer-Regular [FTH0021]
Low VOC Topcoat Reducer-Slow [FTH0023]
- Film Build
Delta Sealer has a recommended film build thickness of:
WFT (Unreduced) 2.0 - 4.5 mils 50 - 114 microns
DFT 1 - 2 mils 25 - 50 microns
The recommended dry film thickness is above the blast/sanding profile.
Theoretical coverage at 1.0 mil (25 microns)
DFT: 732 ft² per gallon at 100% transfer efficiency.
- Dry Times
20°C 30°C 40°C Top Coat 60 Minutes Full Cure 7 - 9 Days Note: Dry Times are subject to ambient conditions (temperature and humidity), good airflow and film build of primer. For best results surface temperature must be 86°F (30°C) or less before top coating. Maximum re-coat window without sanding is 72 hours at 68°F (20°C) Recommended Sanding 220 - 320 grit after the topcoat window has been exceeded.
- Top Coating Infomation
Delta Sealer can be topcoated with the entire range of Endura topcoat products.
- Clean Up
Clean all equipment immediately after use with Endura High Strength Gun Wash, Endura epoxy reducer or Endura EX-2C thinner.
Properties
- Finish
- Low Gloss
- Typical Properties
- Specifications
| Value | Units | Test Method / Conditions | |
| Volume Solids Mixed | 44 - 48 | % | — |
| VOC Mixed (Unreduced) | 333.0 | g/l | EPA Method 24 |
| Value | Units | Test Method / Conditions | |
| Solvent Resistance (100 MEK Rubs) | No Failure | — | ASTM D4752 |
| Impact Resistance (30 in. lbs) | No Failure | — | ASTM D2794 |
| Flexibility (1/4 in. Mandrel Bend) | No Failure | — | ASTM D522 |
| Service Temperature | -40 to 182 | °C | — |
Safety & Health
- Environmental Conditions
For optimum coating performance, product, substrate and ambient temperature should be between 68°F-77°F (20°C-25°C). To prevent condensation during application the surface temperature must be 5°F (3°C) or more above the dew point at all times.
Packaging & Availability
- Ordering Information (Sizing)
Available in Quarts, Gallons and Pails Other Custom sizes may be available.
2 Mixed Quarts (1.89 L) Comp A - Gray 2X FUA0211-020 946 ml Comp B FUB0211-022 473 ml 1.25 Mixed Gallons (4.73 L) Comp A - Gray FUA0211-030 3.78 L Comp B FUB0211-020 946 ml 5 Mixed Gallon (18.9 L) Comp A - Gray FUA0211-054 15.1 L Comp B FUB0211-030 3.78 L
Storage & Handling
- Pot Life (25°C, 50% RH)
- 8 Hours
- Shelf Life
- 3 Years (Component A, 25°C), 2 Years (Component B, 25°C)