Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Benefits
- Simple preparation (1:1 mixing ratio).
- Can be shaped to required profile.
- Repositioning possible for up to 30 minutes.
- Does not shrink.
- Excellent chemical resistance.
- Good adhesion to a variety of metals, ceramics and hard plastics.
Applications & Uses
- Applications
- Basic Uses
MIX2FIX GP Aluminum spreads and applies easily to fill large and small gaps on both horizontal and vertical surfaces. When fully cured, conventional metalworking techniques can be used to machine, file, drill, sand, and paint the finished repair. Use MIX2FIX GP Aluminum to fill holes and cracks; repair broken, worn or damaged parts such as castings, valve bodies, low-pressure pipes, fabrications, tanks, wood and metal fittings; level machinery; make small-scale parts, models, templates and molds; as a general-purpose repair product for aluminum parts, profiles, extrusions and plates.
- Applications Limitations
- Does not adhere to polyethylene, polypropylene or PTFE.
- See performance data for temperature limits.
- Do not apply at temperatures below 41°F (5°C).
- Not intended for structural applications.
- How to use
Surface Preparation
All surfaces should be clean, dry and free from all contamination, particularly oils and greases, which will impair bond and could lead to premature failure. Ideally surfaces should be abraded with a fine emery cloth, followed by a solvent wipe with dry acetone or commercially available degreaser. Apply mixed product immediately after cleaning to avoid possible post-cleaning contamination.
Mixing and Application
Small quantities can be mixed by hand using a spatula or palette knife; larger quantities can be machine-mixed. Wear impermeable gloves when mixing or handling uncured product. Measure out equal volumes or weights of the two components, using different utensils for each to avoid contamination. Use only the amount needed for the job at hand. Mix thoroughly for a minimum of 3 minutes until uniform in color. Use spatula or palette knife to apply to clean, dry surface. Mixed product should be used within 25 to 30 minutes to ensure maximum adhesion. Applying product after this time may impair bond strength. Remove excess material before the paste has set. To achieve a glossy finish, smooth the surface immediately after application with a knife moistened with a solvent such as acetone or mineral spirits. Working time is 60 minutes at 68°F (20°C), but it is recommended that repairs be completed within 30 minutes to avoid disturbing the repair as it begins to set. MIX2FIX GP Aluminum will start setting within an hour at 68°F (20°C), depending on volume and temperature: the greater the volume (or higher the temperature), the faster it will set. Allow 6 hours before handling and 48 hours before returning to service. The application can be shaped, filed and polished after 48 hours.
Properties
- Cured Properties
- Uncured Properties
| Value | Units | Test Method / Conditions | |
| Chemical Resistance | Resistant to hydrocarbons, ketones, alcohols, esters, halocarbons, aqueous salt solutions, dilute acids and bases | — | — |
| Compressive Strength | 10,000 (69) | psi (MPa) | — |
| Hardness, (7 Day Cure 73°F (23°C)) | 75.0 | Shore D | — |
| Lap Shear Tensile Strength On Steel | 2,175 (15) | psi (MPa) | — |
| On Aluminum | 1,300 (9) | psi (MPa) | — |
| Physical Appearance | Metallic aluminum-gray solid | — | — |
| Temperure Limits Continuous | -4 to +248 (-20 to +120) | °F(°C) | — |
| Temperure Limits Intermittent | -4 to +302 (-20 to +150) | °F(°C) | — |
| Tensile Strength | 2,500 (17.5) | psi (MPa) | — |
| Value | Units | Test Method / Conditions | |
| Applicion Temperure | 50 to 95 (10 to 35) | °F(°C) | — |
| Composition | Aluminum-filled epoxy resin | — | — |
| Handling Time 68°F (20°C) | 6.0 | hours | — |
| Maximum Thickness In One Pass (<12 Mm) | max. 0.47 | — | — |
| Mixed Density | 15 (1.8) | lb/gl( g/cm3)) | — |
| Mixing Rio By Weight And Volume | 0.04236111111111111 | — | — |
| Odor (Hardener) | Faint amine smell (no odor when cured) | — | — |
| Physical Appearance | Paste | — | — |
| Return To Service Time (73°F (23°C)) | 48.0 | hours | — |
| Viscosity | 6,50,000 | cps | — |
| Work Life (68°F (20°C)) | 1.0 | hour | — |
Safety & Health
- Health Precautions
Contains Epoxy Resin. Epoxies are skin/eye irritants and known sensitizers. Direct product contact may cause an allergic reaction in some individuals. Avoid skin/eye contact. Wear impermeable gloves when mixing or handling uncured product. Inhalation of dust may be harmful. Avoid inhalation of dust. Wear dust mask and protective eyewear when sanding cured product. Ingestion of product may be harmful. Avoid ingestion. KEEP OUT OF THE REACH OF CHILDREN.
Packaging & Availability
- Packaging
Available for private label. Minimum batch quantities apply. Packaging options to be determined.