Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
Applications & Uses
- Applications
- Compatible Substrates & Surfaces
- Intended Uses
A high performance potable water certified tank primer for maintenance and repair projects used in combination with Easy Flex or Easy Novo. Moisture tolerant concrete and concrete tank lining primer.
- Surface Preparations
- Simply stated the steel surface must be:
- Clean: No staining to white rag when rubbed across steel surface
- Dry: No visible moisture on the steel surface
- Tight: No loose material when a wire brush is pulled across the surface of the metal
- Hydro-blast or Slurry-blast to SSPC-SP2 or ST2 standard. A surface profile of 50 - 100 microns is required. Weld Seams and sharp edges must be stripe coated with Easy Prime.
- New Concrete must cure minimum of 28 days prior to application.
- Application
Film Thickness
- 4 Wet Mils (100 microns wet). Sagging will occur greater than 4 wet mils in a single coat.
Theoretical Coverage
- 9.88 m²/liter (400 Ft2/Gall) at 4 Mils , add 20% for overspray
Method of Application : Overspray loss. Airless Spray, Brush, Roller
Mixing
Material is supplied in a Uni-Pak container. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified.
- Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.
Thinner
Not recommended.
Airless Spray
Recommended
- Tip Range 0.53-0.58 mm (21-23 thou)
- Total output fluid pressure at spray tip not less than 211 kg/cm² (3000 p.s.i.)
- Mixed material temperatures should be between 30-35°C (86 - 95°F) for optimum spraying.
Conventional Spray
Application by conventional spray is not recommended
Brush
Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.
Roller
Application by roller is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.
Cleaner
Methyl Ethyl Ketone (CAS # 78-93-3)
Work Stop / Cleanup
Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with Cleaner. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed material. Clean all equipment immediately after use with cleaner. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.
Welding
In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.
- Limitations
At ambient temperatures below 25°C paint lines must be lagged. In-line heaters should not be used unless absolutely necessary. For maximum performance the curing temperature should be kept below 35°C. Particular care should be taken to avoid exceeding this in localized areas when artificial heating is introduced. The climatic conditions within the tank must be controlled to maintain a maximum relative humidity of 90%. The drying times and overcoating intervals may alter due to various on-site factors such as tank configuration and ventilation rates.
- Potable Water Tank
Back in to Service Time for Complete System (Easy Prime + Easy Flex)
Drying Information 10°C 15°C 25°C 35°C Curing Duration no data 60 hrs 48 hrs 36 hrs Once the curing duration is complete, flush fresh water tank once prior to use.
Properties
- Color
- Typical Properties
- Performance Properties
| Value | Units | Test Method / Conditions | |
| Part A (Color) | 221 - Green | — | — |
| Sheen | Gloss | — | — |
| Part B (Curing Agent) | 222.0 | — | — |
| Volume Solids (Wet mils = Dry mils) | 100.0 | % | ISO 3233:1998 |
| Typical Density | 1.1- 1.3 | — | — |
| Mix Ratio | 2.25 : 1 | — | — |
| Flash Point (Typical, Part A) | min. 100 | °C | — |
| Flash Point (Typical, Part B) | min. 100 | °C | — |
| Flash Point (Typical, Mixed) | min. 100 | °C | — |
| Drying Information (Touch Dry, 10°C) | 24 | Hours | ISO 9117/3:2010 |
| Drying Information (Hard Dry, 10°C) | 36 | Hours | ISO 9117-1:2009 |
| Drying Information (Touch Dry, 15°C) | 12 | Hours | ISO 9117/3:2010 |
| Drying Information (Hard Dry, 15°C) | 24 | Hours | ISO 9117-1:2009 |
| Drying Information (Touch Dry, 25°C) | 8 | Hours | ISO 9117/3:2010 |
| Drying Information (Hard Dry, 25°C) | 18 | Hours | ISO 9117-1:2009 |
| Drying Information (Touch Dry, 35°C) | 5 | Hours | ISO 9117/3:2010 |
| Drying Information (Hard Dry, 35°C) | 8 | Hours | ISO 9117-1:2009 |
| Value | Units | Test Method / Conditions | |
| Adhesion Pull Test | 120 (1,700) | kg/cm²(psi) | ASTM D4541 |
| Elongation | 3.05 (27) | Joules(inch pounds) | ASTM D2794 |
| Conical Mandrel Bend | min. 34 | — | ASTM D522 |
| Water Vapor Transmission | 0.0043 | Perm cm | ASTM D1653 |
| Heat Resistance Continuous | 150 (302) | °C(°F) | ASTM D2485 |
| Salt Fog (2,000 Hour) | Pass | — | ASTM B117 |
Regulatory & Compliance
- Certifications
All Certification are NSF ANSI Standard 61 unless otherwise noted
- Potable Water - Carriage of Potable Water
- Potable Water - Certification for tanks greater than or equal to 200 gallons
- Potable Water - Certification for pipe diameter greater than or equal to 24"
- Potable Water - Certification for pipe fitting diameter greater than or equal to 2"
- Potable Water - Certification for surface area to volume ratio not to exceed 67.7 cm2/L
- Seawater Ballast Tanks - Maintenance survey (Lloyd's Register)
- Certificate of Design Assessment - Ballast tank repair (American Bureau of Shipping)
Technical Details & Test Data
- Substrate Temperature
Overcoat
10°C 15°C 25°C 35°C Min Max Min Max Min Max Min Max 30 hrs Unlimited 18 hrs Unlimited 12 hrs Unlimited 4 hrs Unlimited
Packaging & Availability
- Packaging Type
- Packaging
10 Liter UniPak Pail (2.64 Gall) Mixed , 30 lBS Gross Weight
Storage & Handling
- Shelf Life
- 36 Months
- Pot Life
Pot Life (35°C) 45 mins Pot Life (25°C) 60 mins Pot Life (15°C) 90 mins