Knowde Enhanced TDS
Identification & Functionality
- Carrier
- Chemical Family
- Product Type
- Pigment Type
- Varies with color
- Resin Type
- Acrylic Copolymer
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
Applications & Uses
- Compatible Substrates & Surfaces
- Product Application
Surface Preparation:
All Surfaces: Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with Krud Kutter Original Cleaner Degreaser, commercial detergent or other suitable cleaner. Mold and mildew must be cleaned with a chlorinated cleaner or bleach solution. Rinse thoroughly with fresh water and allow to fully dry. All surfaces must be dry at time of application.
Steel: Hand tool (SSPC-SP-2) or power tool (SSPC-SP-3) clean to remove loose rust, mill scale, and deteriorated previous coatings. Abrasive blasting to a minimum Commercial Grade (SSPC-SP-6, NACE 3) with a 1-2 mil (25-50 μ) surface profile is recommended for optimal performance. Abrasive blast cleaned steel requires two coats.
Concrete and Masonary: Hand or power tool clean to remove all loose or unsound concrete, masonry, or previous coating. Very dense, non-porous concrete should be acid etched or abrasive blasted to remove the laitance layer and create a surface profile. Allow new concrete to cure for 30 days before coating.
Previously Coated: Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile. The 5200 System DTM Acrylic Finish is compatible with most coatings, but a test patch is suggested.
Application: Apply only when the air and surface temperatures are between 50-100°F (10-38°C) and the surface temperature is at least 5°F (3°C) above the dew point. The relative humidity should not be greater than 85%. Extremely high or low relative humidity can effect dry times and the final gloss of the coating. Iron oxide staining may occur with some colors if surface and air temperature are below 60°F (16°C) or the relative humidity is above 70% during the time of application. For optimum performance use a primer. For optimum hiding, additional coats of 5215 Alumni-Non may be required over dark colors.
Equipment Recommendations:
(Comparable equipment also suitable)
Brush: Use a good quality synthetic bristle brush.
Roller: Use a good quality short nap synthetic fiber roller cover (1/4-3/8”)Equipment Recommendations:
Air atomised spray:
Method Fluid Tip Fluid Delivery Atomized Pressure
Pressure 0.055-0.070 10-16 oz./min. 25-60 psi Siphon 0.055-0.070 25-60 psi HVLP (var.) 0.043-0.070 8-10 oz./min. 10 psi (at tip) Airless Spray:
Fluid Pressure Fluid Tip Filter Mesh 1,800-3,000 psi 0.013-0.017 100 Thinning:
Brush/Roller: Thinning is not recommended
Air Atomised Spray: Up to 1 pint per gallon.Cleanup: Soap and water.
Properties
- Color
- Typical Properties
| Value | Units | Test Method / Conditions | |
| 60° Gloss (Eggshell) | 5 - 15 | % | ASTM D2243 |
| 60° Gloss (Gloss) | 10 - 100 | % | ASTM D2243 |
| 60° Gloss (Satin) | 10 - 20 | % | ASTM D2243 |
| 60° Gloss (Semi Gloss) | 35 - 55 | % | ASTM D2243 |
| Conical Flexibility | min. 33 | % | ASTM D522 |
| Cyclic Prohesion (2 Cycles, 672 hours) | Rating 10 | - | ASTM D5894 |
| Dry Heat Resistance | 200.0 | °F | - |
| Dry Times (70-80°F and 50% Relative Humidity, Handle) | 2 - 4 | hours | - |
| Dry Times (70-80°F and 50% Relative Humidity, Recoat) | 1 - 3 | hours | - |
| Dry Times (70-80°F and 50% Relative Humidity, Tack Free) | 1 - 2 | hours | - |
| Impact Resistance (Direct) | min. 160 | lbs | ASTM D2794 |
| Impact Resistance (Reverse) | min. 160 | lbs | ASTM D2794 |
| Pencil Hardness | 2B | - | ASTM D3363 |
| Practical Coverage (Recommended DFT, Assumes 15% material loss) | 150 - 240 | sq. ft./gal. | - |
| Recommended Dry Film Thickness (DFT, Per Coat) | 2 - 3 | mils | - |
| Solids (By weight) | 35 - 45 | % | - |
| Solvents | Water and Methyl Carbitol | - | - |
| Theoretical Coverage (1 mil DFT, 25μ) | 530 - 560 | sq. ft./gal. | - |
| Volatile Organic Compounds | max. 250 | g/l | - |
| Weight (Per Gallon) | 8.5 - 9.9 | lbs | - |
| Wet Film to Achieve DFT | 5 - 9 | mils | - |
Regulatory & Compliance
- Certifications & Compliance
- Regulatory
This product complies with USDA FSIS regulatory sanitation performance standards for food establishment facilities. This coating is impervious to moisture and easily cleaned and sanitized.
MPI #15, #153, #161, #164 Certified
Packaging & Availability
- Availability
Gloss Finish:
1-Gallon 5-Gallon Description 5222402 Marlin Blue 5225402 Safety Blue 5227402 National Blue 5233402 Safety Green 5234402 Green (John Deere)
5235402 Vista Green 5237402 Forest Green 5256402 International Orange
5271402 5271300 Dunes Tan 5277402 Chestnut Brown 5279402 Black 5282402 5282300 Silver Gray 5286402 5286300 Navy Gray 5288402 Machine Tool Gray
5292402 5292300 White 5215402 Alumi-Non 5244402 286905 Safety Yellow 5255402 5255300 Safety Orange 5264402 286904 Safety Red 5265402 Fire Hydrant Red
Gloss Finish Tint Bases:
1-Gallon 5-Gallon Description 5207411 5207391 Masstone 5208418 5208394 Deep 5209417 5209397 Light Satin Finish:
1-Gallon 5-Gallon Description 285057 285058 Safety Yellow 285059 285060 Safety Red 285062 285063 Safety Blue 285066 285068 Safety Orange 285069 285071 Safety Green Semi Gloss Finish:
1-Gallon 5-Gallon Description 5293402 5293300 Semi-Gloss White
5274402 286903 Semi-Gloss Black
Egg Shell Finish:
1-Gallon 5-Gallon Description 5278402 286901 Black 5290402 286902 White 5258402 5258300 Tower Orange 5291402 5291300 Tower White 5275402 Bronzetone Egg Shell Finish Tint Bases:
1-Gallon 5-Gallon Description 5211411 286919 Masstone 5212418 286925 Deep 5213417 286930 Light The tint bases use the Rust-Oleum Water-Based Colorants. Made to Order only. Contact Rust-Oleum Customer Service for details.
For spray application only. For optimum hiding, use two or more coats.
Tint Base Maximum Colorant per gallon:
Quantity Description 12 Oz. Masstone 8 Oz. Deep 4 Oz. Light - Companion Products
Primers Eggshell Finish:
1-Gallon 5-Gallon Description 5269402 Red 5281402 5281300 Gray
Storage & Handling
- Shelf Life
- 5 Years