Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Features & Benefits
Applications & Uses
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ⁴² Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ²² Suggest to use narrow mold temperature 140C~160C for NMT application. Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ⁴⁹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- ⁵⁹ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ¹² Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
Value | Units | Test Method / Conditions | |
Flexural Modulus (1.3 mm/min, 50 mm span)⁴⁹ | 7400 | MPa | ASTM D790 |
Flexural Modulus (2 mm/min)⁴⁹ | 7900 | MPa | ISO 178 |
Flexural Stress at Break (1.3 mm/min, 50 mm span)⁴⁹ | 170 | MPa | ASTM D790 |
Flexural Stress at Break (2 mm/min)⁴⁹ | 168 | MPa | ISO 178 |
Tensile Modulus (1 mm/min)⁴⁹ | 8600 | MPa | ISO 527 |
Tensile Modulus (5 mm/min)⁴⁹ | 8700 | MPa | ASTM D638 |
Tensile Strain at Break (5 mm/min)⁴⁹ | 2.4 | % | ISO 527 |
Tensile Strain at Break (Type I, 5 mm/min)⁴⁹ | 2.4 | % | ASTM D638 |
Tensile Stress at Break (5 mm/min)⁴⁹ | 110 | MPa | ISO 527 |
Tensile Stress at Break (Type I, 5 mm/min)⁴⁹ | 110 | MPa | ASTM D638 |
Value | Units | Test Method / Conditions | |
Density⁴⁹ | 1.49 | g/cm³ | ISO 1183 |
Melt Flow Rate (at 250°C/5.0 kgf)⁴⁹ | 21 | g/10 min | ASTM D1238 |
Melt Flow Rate (at 275°C/5 kgf)⁴⁹ | 37 | g/10 min | ASTM D1238 |
Melt Volume Rate (at 250°C/5.0 kg)⁴⁹ | 15 | cm³/10 min | ISO 1133 |
Melt Volume Rate (at 275°C/5 kg)⁴⁹ | 29 | cm³/10 min | ISO 1133 |
Moisture Absorption (at 23°C/50% RH/24hrs)⁴⁹ | 0.07 | % | ISO 62-4 |
Mold Shrinkage - flow¹²,⁴⁹ | 0.2 - 0.3 | % | SABIC method |
Mold Shrinkage - xflow¹²,⁴⁹ | 0.4 - 0.5 | % | SABIC method |
Specific Gravity⁴⁹ | 1.5 | - | ASTM D792 |
Value | Units | Test Method / Conditions | |
Vicat Softening Temperature Rate (B/120)⁴⁹ | 0.000105 | °C | ASTM D1525 (ISO 306) |
Vicat Softening Temperature Rate (B/50)⁴⁹ | 0.000105 | °C | ASTM D1525 (ISO 306) |
CTE - flow (at -40°C to 40°C)⁴⁹ | 2.4e-05 | 1/°C | ASTM E831 |
CTE - xflow (at -40°C to 40°C)⁴⁹ | 0.00013 | 1/°C | ASTM E831 |
HDT - Unannealed (0.45 MPa, 3.2 mm)⁴⁹ | 215 | °C | ASTM D648 |
HDT - Unannealed (1.82 MPa, 3.2mm)⁴⁹ | 172 | °C | ASTM D648 |
HDT/Af (1.8 MPa Flatw 80*10*4 sp=64mm)⁴⁹ | 188 | °C | ISO 75/Af |
HDT/Bf (0.45 MPa Flatw 80*10*4 sp=64mm)⁴⁹ | 216 | °C | ISO 75/Bf |
Value | Units | Test Method / Conditions | |
Charpy (at 23°C, V-notch Edgew 80*10*3 sp=62mm)⁴⁹ | 13 | kJ/m² | ISO 179/1eA |
Charpy (at -30°C, V-notch Edgew 80*10*3 sp=62mm)⁴⁹ | 11 | kJ/m² | ISO 179/1eA |
Charpy (Unnotch Edgew, at 23°C, 80*10*3 sp=62mm)⁴⁹ | 52 | kJ/m² | ISO 179/1eU |
Izod Impact Notched (80*10*4 +23°C)⁴⁹ | 13 | kJ/m² | ISO 180/1A |
Izod Impact Notched (80*10*4 -30°C)⁴⁹ | 8 | kJ/m² | ISO 180/1A |
Izod Impact Notched (at 23°C)⁴⁹ | 131 | J/m | ASTM D256 |
Izod Impact Notched (at -30°C)⁴⁹ | 90 | J/m | ASTM D256 |
Izod Impact Unnotched (80*10*4 +23°C)⁴⁹ | 45 | kJ/m² | ISO 180/1U |
Izod Impact Unnotched (at 23°C)⁴⁹ | 750 | J/m | ASTM D4812 |
Value | Units | Test Method / Conditions | |
Drying Temperature⁴² | 100 - 120 | °C | — |
Drying Time (Cumulative)⁴² | 8 | Hrs | — |
Drying Time⁴² | 2 - 4 | Hrs | — |
Front - Zone 3 Temperature⁴² | 250 - 270 | °C | — |
Hopper Temperature⁴² | 40 - 60 | °C | — |
Maximum Moisture Content⁴² | 0.02 | % | — |
Melt Temperature⁴² | 250 - 270 | °C | — |
Middle - Zone 2 Temperature⁴² | 250 - 270 | °C | — |
Mold Temperature²² | 140 - 160 | °C | — |
Nozzle Temperature⁴² | 245 - 275 | °C | — |
Rear - Zone 1 Temperature⁴² | 240 - 260 | °C | — |
Value | Units | Test Method / Conditions | |
UL Recognized 94HB Flame Class Rating⁵⁹ | min. 0.7 | mm | UL 94 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability